基于流固耦合的蒸汽发生器换热管结构应力分析

孙宝芝; 郑陆松; 韩文静; 张国磊; 刘尚华

doi:10.3969/j.issn.0438-1157.2014.z1.059

您当前的位置：

首页 >

文章列表页 >

基于流固耦合的蒸汽发生器换热管结构应力分析

流体力学与传递现象 | 更新时间：2025-12-10

- 基于流固耦合的蒸汽发生器换热管结构应力分析
- Analysis on structural stress of tube in steam generator based on fluid-structure interaction
- 化工学报 2014年第S1期页码：364-370
- 作者机构：
  
  哈尔滨工程大学动力与能源工程学院,黑龙江,哈尔滨,150001
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.z1.059
  中图分类号： Q028.8
- 网络首发：2014-05-30，
  
  纸质出版：2014-05-30
- 稿件说明：
移动端阅览
孙宝芝, 郑陆松, 韩文静, 等. 基于流固耦合的蒸汽发生器换热管结构应力分析[J]. 化工学报, 2014,(S1):364-370.

SUN Baozhi, ZHENG Lusong, HAN Wenjing, et al. Analysis on structural stress of tube in steam generator based on fluid-structure interaction[J]. CIESC Journal, 2014, (S1): 364-370.
孙宝芝, 郑陆松, 韩文静, 等. 基于流固耦合的蒸汽发生器换热管结构应力分析[J]. 化工学报, 2014,(S1):364-370. DOI： 10.3969/j.issn.0438-1157.2014.z1.059.

SUN Baozhi, ZHENG Lusong, HAN Wenjing, et al. Analysis on structural stress of tube in steam generator based on fluid-structure interaction[J]. CIESC Journal, 2014, (S1): 364-370. DOI： 10.3969/j.issn.0438-1157.2014.z1.059.

摘要

以核电站蒸汽发生器为研究对象，采用两流体模型描述二次侧汽液两相流动及沸腾换热，利用CFX对一、二次侧流体与换热管及支撑板的耦合流动换热进行三维数值模拟，在此基础上提取一、二次侧流体压力载荷，在Workbench平台中实现载荷向结构模型的传递，计算换热管结构应力。流固耦合计算结果表明：支撑板位置处二次侧流体流速迅速增大又快速减小，并且流体湍流耗散急剧增大造成二次侧流体压力损失增大；换热管压力应力取决于一、二次侧流体压差，整体平均压力应力约为58 MPa，与实际测量参数相符。

Abstract

Taken the steam generator of nuclear power plant as the prototype

the vapor-liquid two-phase flow and the boiling heat transfer were simulated by two-fluid model. The coupled flow and heat transfer process between the fluid of the primary and secondary sides and the heat transfer tubes with support plates was numerically simulated using CFX software. Based on the flow and heat transfer calculation

the pressure of fluid in the primary and secondary sides was extracted. The pressure load was transferred to the structure model in Workbench. And the structural stress of tube was calculated. The fluid-structure interaction results show that there is an abrupt increase in secondary velocity at the positions of support plates. The fluid pressure loss of secondary side increases because of the increase of fluid turbulence dissipation. The pressure stress of the heat transfer tube depends on the pressure difference between the primary side and the secondary side. The overall average of the pressure stress is about 58 MPa

which is consistent with the actual measured parameter.

关键词

Keywords

references

浏览量

389

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

基于丝网探针的螺旋管内气液两相流气泡行为研究

聚合釜传热性能的实验研究及数值模拟

穿流-刚柔组合桨强化固液两相的悬浮行为

直管式直流蒸汽发生器不同运行参数下两相流压降预测

基于流固耦合的错位桨搅拌假塑性流体动力学特性