大菱形孔端面密封力变形及密封性能分析

程香平; 孟祥铠; 彭旭东

doi:10.3969/j.issn.0438-1157.2014.08.033

您当前的位置：

首页 >

文章列表页 >

大菱形孔端面密封力变形及密封性能分析

表面与界面工程 | 更新时间：2025-12-10

- 大菱形孔端面密封力变形及密封性能分析
- Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores
- 化工学报 2014年第8期页码：3089-3097
- 作者机构：
  
  1. 浙江工业大学机械工程学院,浙江,杭州,310032
  2. 浙江工业大学过程装备及其再制造教育部工程研究中心,浙江,杭州,310032
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.08.033
  中图分类号： H117.2
- 网络首发：2014-08-05，
  
  纸质出版：2014-08-05
- 稿件说明：
移动端阅览
程香平, 孟祥铠, 彭旭东. 大菱形孔端面密封力变形及密封性能分析[J]. 化工学报, 2014,(8):3089-3097.

CHENG Xiangping, MENG Xiangkai, PENG Xudong. Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores[J]. CIESC Journal, 2014, (8): 3089-3097.
程香平, 孟祥铠, 彭旭东. 大菱形孔端面密封力变形及密封性能分析[J]. 化工学报, 2014,(8):3089-3097. DOI： 10.3969/j.issn.0438-1157.2014.08.033.

CHENG Xiangping, MENG Xiangkai, PENG Xudong. Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores[J]. CIESC Journal, 2014, (8): 3089-3097. DOI： 10.3969/j.issn.0438-1157.2014.08.033.

摘要

针对等深大菱形孔端面液体润滑机械密封，采用有限差分法求解等温及层流不可压缩二维Reynolds方程，获得液膜压力场。利用商用有限元软件计算密封环三维固体变形，对不同操作工况条件下和不同结构的密封环的力变形、摩擦扭矩、液膜刚度及泄漏率等性能参数进行了计算。结果表明：大菱形孔流体动压型机械密封端面产生周向波度和径向锥度变形；改变工况条件可使密封面形成收敛和发散两种不同的变形，密封性能参数因此产生显著变化；当面积比B=0.65～0.75时，大菱形孔端面密封可获得较好的密封性能；辅助密封圈O形圈位置l对径向锥度变形具有很大影响，l优选值范围为2.4～4.0 mm。

Abstract

For a liquid lubricated end face mechanical seal with diamond macro-pores

the finite difference method was used to solve the two-dimension Reynolds equation for the isothermal

laminar and incompressible lubrication film and film pressure distribution was obtained. Finite element software was used to calculate surface deformation of seal rings. Deformation and seal performance parameters

such as friction torque

liquid film stiffness and leakage rate were investigated under different operating conditions for different sealing rings constructions. The results showed that the end face of mechanical seal deformed with circumferential waviness and radial coning. Convergent and divergent deformations occurred according to different operating conditions

hence seal performance greatly changed. When B was 0.65-0.75

the mechanical seal could achieve better sealing performance. The location of the secondary O ring greatly influenced radial taper deformation

the range of l preferred values was 2.4-4.0 mm.

关键词

Keywords

references

浏览量

277

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

非规则V形表面织构化机械端面密封性能研究

不同截面肋柱-软尾结构单相流动传热比较

润滑油在内插同轴交叉翼型涡产生器管内流动与传热特性分析

内插不同形状涡产生器管内层流流动与传热特性的对比分析

原位水热法可控合成Bi2MoO6/MoO3复合纤维及其高效光催化产氢性能