采用UNIFAC模型预测催化裂化分区转化中原料的汽化率

金楠; 王刚; 徐春明; 高金森

doi:10.3969/j.issn.0438-1157.2014.07.031

您当前的位置：

首页 >

文章列表页 >

采用UNIFAC模型预测催化裂化分区转化中原料的汽化率

热力学 | 更新时间：2025-12-10

- 采用UNIFAC模型预测催化裂化分区转化中原料的汽化率
- Predicting vaporization of feedstock in zoning catalytic cracking by UNIFAC model
- 化工学报 2014年第7期页码：2710-2716
- 作者机构：
  
  中国石油大学(北京)重质油国家重点实验室,北京,102249
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.07.031
  中图分类号： E624
- 网络首发：2014-07-05，
  
  纸质出版：2014-07-05
- 稿件说明：
移动端阅览
金楠, 王刚, 徐春明, 等. 采用UNIFAC模型预测催化裂化分区转化中原料的汽化率[J]. 化工学报, 2014,(7):2710-2716.

JIN Nan, WANG Gang, XU Chunming, et al. Predicting vaporization of feedstock in zoning catalytic cracking by UNIFAC model[J]. CIESC Journal, 2014, (7): 2710-2716.
金楠, 王刚, 徐春明, 等. 采用UNIFAC模型预测催化裂化分区转化中原料的汽化率[J]. 化工学报, 2014,(7):2710-2716. DOI： 10.3969/j.issn.0438-1157.2014.07.031.

JIN Nan, WANG Gang, XU Chunming, et al. Predicting vaporization of feedstock in zoning catalytic cracking by UNIFAC model[J]. CIESC Journal, 2014, (7): 2710-2716. DOI： 10.3969/j.issn.0438-1157.2014.07.031.

摘要

以不同减压馏分油（VGO）/减压渣油（VR）混合比例的重油为研究对象，采用基团贡献模型（UNIFAC）预测了常规催化裂化工艺（FCC）与分区催化裂化工艺（ZCC）中原料的汽化率。在所考察的催化裂化油剂混合条件下，原料的汽化率均大于70%（质量分数）。高油剂混合温度使饱和蒸气压升高，而大雾化水蒸气量有利于降低油气分压使泡露点温度降低，均使原料汽化率升高。VR掺炼比例对原料汽化率影响很大，当掺炼比例从30%（质量分数）提高至50%（质量分数）时，原料汽化率降低5.44%～7.53%（质量分数）。当VR掺炼比例较低（<50%）时，常规FCC工艺比ZCC工艺的原料汽化率高，当VR掺炼比例达到50%时，ZCC工艺的分开进料方式更有利于原料的汽化。这取决于VGO对VR的分散作用和VGO与VR的竞争汽化造成的影响。

Abstract

A novel zoning catalytic cracking (ZCC)

which processed vacuum gas oil (VGO) and vacuum residue (VR) in different zones under respective optimal conditions to avoid competitive adsorption effect

was proposed. Aiming at comparing routine fluid catalytic cracking (FCC) with ZCC

vaporization of feedstock was predicted with the UNIFAC model. Vaporization of feedstock was higher than 70% (mass) in both ZCC and FCC under investigated conditions. Higher oil-catalyst-mixing temperature

less atomized steam and lower VR blending ratio were beneficial to feedstock vaporization. Vaporization of feedstock decreased by 5.44%－7.53%(mass) when VR blending ratio increased from 30%(mass) to 50%(mass). When VR blending ratio was lower than 50%(mass)

vaporization of separate feedstocks in ZCC was lower than that of blending feedstock in routine FCC. When VR blending ratio reached 50%(mass)

separate feeding used in ZCC was more beneficial to vaporization of feedstock. That was the result of the influence of dispersion effect of VGO on VR and competitive vaporization between VGO and VR.

关键词

Keywords

references

浏览量

324

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

原料油汽化特性对催化裂化反应结焦过程影响的CFD模拟

一种分步约简的炼油生产敏感变量选择方法

基于核慢特征回归与互信息的常压塔软测量建模

RFCC化学汽提过程的模拟研究

基于多源信息特征融合的抽油井动液面集成软测量建模