PPy/CS复合电极热压成型条件的优化

赵春霞; 薛娟琴; 张玉洁; 李国平; 罗瑶

doi:10.11949/j.issn.0438-1157.20151833

您当前的位置：

首页 >

文章列表页 >

PPy/CS复合电极热压成型条件的优化

材料化学工程与纳米技术 | 更新时间：2025-11-26

- PPy/CS复合电极热压成型条件的优化
- Optimization of hot press molding conditions for making PPy/CS composite electrodes
- 化工学报 2016年67卷第10期页码：4514-4520
- 作者机构：
  
  西安建筑科技大学冶金工程学院,陕西,西安,710055
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20151833
  中图分类号： Q317.4
- 网络首发：2016-10-05，
  
  纸质出版：2016-10-05
- 稿件说明：
移动端阅览
赵春霞, 薛娟琴, 张玉洁, 等. PPy/CS复合电极热压成型条件的优化[J]. 化工学报, 2016,67(10):4514-4520.

ZHAO Chunxia, XUE Juanqin, ZHANG Yujie, et al. Optimization of hot press molding conditions for making PPy/CS composite electrodes[J]. CIESC Journal, 2016, 67(10): 4514-4520.
赵春霞, 薛娟琴, 张玉洁, 等. PPy/CS复合电极热压成型条件的优化[J]. 化工学报, 2016,67(10):4514-4520. DOI： 10.11949/j.issn.0438-1157.20151833.

ZHAO Chunxia, XUE Juanqin, ZHANG Yujie, et al. Optimization of hot press molding conditions for making PPy/CS composite electrodes[J]. CIESC Journal, 2016, 67(10): 4514-4520. DOI： 10.11949/j.issn.0438-1157.20151833.

摘要

以壳聚糖（CS）和聚吡咯（PPy）制备的复合材料为活性基体，在不添加黏结剂的条件下，采用热压成型法制备复合电极。重点考察了不同导电剂对电极力学性能的影响，热压温度、成型压力、热压时间及不同种类活性炭对电极电化学性能的影响规律。结果表明：通过热压法不添加黏结剂能够获得性能优良的复合电极；以活性炭为导电剂的电极溶胀性和亲水性最好，且活性炭的比表面积越大电极的电化学性能越好；电极热压成型的最优条件为：热压温度150℃、成型压力10 MPa、热压时间20 min。

Abstract

Electrodes using chitosan (CS) and polypyrrole (PPy) composites as active matrix were fabricated by hot press molding without application of bonding adhesive. The effect of conductive agents on mechanical properties and the influence of fabrication conditions such as hot pressing temperature

molding pressure

hot pressing time and types of activated carbon on electrochemical performances were studied.The experimental results show that high performance composite electrodes were manufactured by this technique. Compared to those of graphite and nano-silver as conductive agent

the electrodes of activated carbon as conductive agent had the best swelling and hydrophilic properties

which also exhibited enhancement in electrochemical performance with the increase of specific surface area of activated carbon. The optimal hot press molding conditions to prepare electrodes were pressing temperature of 150℃

molding pressure of 10 MPa and pressing time of 20 minutes.

关键词

Keywords

references

浏览量

202

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

炭黑/PTFE复合改性石墨毡阴极优化制备及高效电化学产H2O2机理研究

气相沉积硅碳中硅结晶度对电化学性能的影响

分级多孔聚吡咯膜的界面自组装合成与电化学电容性

GeCl4-MxCly-H2体系下锗-杂质竞争沉积热力学研究

硫氰酸红霉素溶解动力学研究