西安交通大学动力工程多相流国家重点实验室,陕西 西安 710049
郭栋(2004—),男,博士研究生,guodong0214@stu.xjtu.edu.cn
赵亮(1971—),男,博士,教授,lzhao@mail.xjtu.edu.cn
收稿:2026-07-09,
修回:2026-09-30,
录用:2026-10-08,
移动端阅览
郭栋, 李逸飞, 赵亮. 高功率LED自然对流非均匀翅片散热器快速评估模型与多目标优化方法[J/OL]. 化工学报, 2026.
GUO Dong, LI Yifei, ZHAO Liang. Rapid evaluation and multi-objective optimization of non-uniform fin heat sinks for high-power LEDs under natural convection[J/OL]. CIESC Journal, 2026.
郭栋, 李逸飞, 赵亮. 高功率LED自然对流非均匀翅片散热器快速评估模型与多目标优化方法[J/OL]. 化工学报, 2026. DOI: 10.11949/0438-1157.20260944.
GUO Dong, LI Yifei, ZHAO Liang. Rapid evaluation and multi-objective optimization of non-uniform fin heat sinks for high-power LEDs under natural convection[J/OL]. CIESC Journal, 2026. DOI: 10.11949/0438-1157.20260944.
针对高功率发光二极管(light-emitting diode,LED)照明灯具自然对流非均匀翅片散热器优化中计算量大、设计变量维数高的问题,提出快速评估与多目标优化方法。以600 W高功率LED灯具自然对流散热器为对象,基于自然对流经验关联式和固—气—辐射热网络构建快速评估模型,并采用区域划分与规律映射将高维、变维非均匀翅片结构转化为17维参数化模型,结合非支配排序遗传算法(Non-dominated Sorting Genetic Algorithm II,NSGA-II)开展平均热流密度、平均温度和最大温差多目标优化。结果表明,对于竖直安装的高功率LED,快速评估模型与计算流体力学(computational fluid dynamics,CFD)结果的关键温度指标相对偏差均小于7%,单次计算时间减少了99.4%;帕累托(Pareto)前沿呈双分支,对应整体低温优先和温度均匀性优先两类非均匀翅片。与原始均匀结构相比,优化结构平均温度最多降低5.4 K,最大温差最多降低6.6 K,表明非均匀翅片可以改善自然对流散热性能。
A rapid evaluation and multi-objective optimization method is proposed to address the high computational cost and high-dimensional design variables in the optimization of non-uniform fin heat sinks for high-power LED lighting fixtures under natural convection. A natural-convection heat sink for a 600 W high-power LED luminaire was taken as the research object. A rapid evaluation model was developed based on empirical correlations of natural convection and a solid–gas–radiation thermal network
and the high-dimensional and variable-dimensional non-uniform fin structures were transformed into a 17-dimensional parametric model using regional division and variation-pattern mapping. The Non-dominated Sorting Genetic Algorithm II (NSGA-II) was employed for the multi-objective optimization of average heat flux density
average temperature
and maximum temperature difference. The results show that
for vertically mounted high-power LEDs
the relative errors of key temperature indicators between the rapid evaluation model and the computational fluid dynamics (CFD) simulations are all less than 7%
and the computation time for a single evaluation is reduced by 99.4%. The obtained Pareto front exhibited a two-branch structure
corresponding to two types of non-uniform fin configurations: one prioritizing overall temperature reduction and the other prioritizing temperature uniformity. Compared with the original uniform-fin structure
the optimized structures reduced the average temperature by up to 5.4 K and the maximum temperature difference by up to 6.6 K. These results indicate that non-uniform fins can effectively improve the heat dissipation performance of natural-convection heat sinks.
Orville T , Tajwar M , Bihani R , et al . Enhancing thermal efficiency in power electronics: a review of advanced materials and cooling methods [J ] . Thermo , 2025 , 5 ( 3 ): 30 .
Kozak D , Nikolaenko Y , Khairnasov S , et al . Radiator temperature regimes for the cooling system of a powerful LED lighting device [J ] . Technology and Design in Electronic Equipment , 2025 ( 1–2 ): 51 - 56 .
Li J N , Yang L . Recent development of heat sink and related design methods [J ] . Energies , 2023 , 16 ( 20 ): 7133 .
Nair V , Baby A , Anoop M B , et al . A comprehensive review of air-cooled heat sinks for thermal management of electronic devices [J ] . International Communications in Heat and Mass Transfer , 2024 , 159 : 108055 .
Adhikari R , Beyragh D , Pahlevani M , et al . A numerical and experimental study of a novel heat sink design for natural convection cooling of LED grow lights [J ] . Energies , 2020 , 13 ( 16 ): 4046 .
李新泽 , 张双星 , 任冠宇 , 等 . 大功率LED热管理用脉动热管热性能 [J ] . 化工学报 , 2024 , 75 ( S1 ): 126 - 134 .
Li X Z , Zhang S X , Ren G Y , et al . Thermal performance of pulsating heat pipe for high power LED thermal management [J ] . CIESC Journal , 2024 , 75 ( S1 ): 126 - 134 .
Nguyen T D , Van Vo A , Bui T T . Design modeling and CFD simulation of parallel plate–fin heat sink under natural convection [J ] . Makara Journal of Technology , 2024 , 28 ( 3 ): 96 - 104 .
Habib N , Siddiqi M , Tahir M . Thermal analysis and optimization of L-shape fin heat sink under natural convection using ANOVA and Taguchi [J ] . Thermal Science , 2022 , 26 ( 2 Part B ): 1519 - 1530 .
McCay O , Nimmagadda R , Ali S M , et al . A parametric design study of natural-convection-cooled heat sinks [J ] . Fluids , 2023 , 8 ( 8 ): 234 .
Tripathy T L , Dash S K . Numerical modeling of natural convection heat transfer from radial branching heat sinks for LED cooling applications [J ] . Applied Thermal Engineering , 2024 , 242 : 122446 .
马奕新 , 金宇 , 张虎 , 等 . 翅片重力热管传热性能实验研究 [J ] . 化工学报 , 2020 , 71 ( 2 ): 594 - 601 .
Ma Y X , Jin Y , Zhang H , et al . Experimental study on heat transfer performance of finned gravity heat pipe [J ] . CIESC Journal , 2020 , 71 ( 2 ): 594 - 601 .
Dong C C , He G N , Meng Z M , et al . Optimality criterion-based latent heat storage heat exchangers topology optimization method [J ] . Journal of Energy Storage , 2025 , 125 : 117012 .
Lindstedt M , Lampio K , Karvinen R . Optimal shapes of straight fins and finned heat sinks [J ] . Journal of Heat Transfer , 2015 , 137 ( 6 ): 061006 .
Haghighi S S , Goshayeshi H R , Safaei M R . Natural convection heat transfer enhancement in new designs of plate-fin based heat sinks [J ] . International Journal of Heat and Mass Transfer , 2018 , 125 : 640 - 647 .
Lampio K , Karvinen R . Optimization of convectively cooled heat sinks [J ] . Microelectronics Reliability , 2017 , 79 : 473 - 479 .
邱燕 , 田茂诚 , 冷学礼 . 封闭空间内纵向外翅片管结构参数对传热的影响 [J ] . 化工学报 , 2013 , 64 ( 7 ): 2405 - 2410 .
Qiu Y , Tian M C , Leng X L . Heat transfer characteristic of longitudinal externally-finned tube in closed space [J ] . CIESC Journal , 2013 , 64 ( 7 ): 2405 - 2410 .
蒋怡娜 . 新型镁合金LED灯具散热器设计与分析 [D ] . 天津 : 天津工业大学 , 2017 .
Jiang Y N . Design and analysis of a novel magnesium alloy heat sink for LED lamps [D ] . Tianjin : Tianjin: Tianjin Polytechnic University , 2017 .
Lee Y J , Kim S J . Thermal optimization of the pin-fin heat sink with variable fin density cooled by natural convection [J ] . Applied Thermal Engineering , 2021 , 190 : 116692 .
Ahmed S W , Altaf K , Tariq A , et al . Geometric optimization of SLM-printed AlSi 10 Mg radial heat sinks: a numerical and experimental approach for natural convection conditions [J ] . Arabian Journal for Science and Engineering , 2024 , 49 ( 11 ): 14643 - 14661 .
Dong C C , Zhang C B , He G N , et al . 3D topology optimization design of air natural convection heat transfer fins [J ] . Nuclear Engineering and Design , 2024 , 429 : 113623 .
倪强 , 厉为民 , 孙艳 , 等 . 大功率LED散热器结构参数对散热的影响研究 [J ] . 现代工业经济和信息化 , 2021 , 11 ( 11 ): 238 - 239 .
Ni Q , Li W M , Sun Y , et al . Study on the effect of structural parameters on heat dissipation in high-power LED heat sinks [J ] . Modern Industrial Economy and Informationization , 2021 , 11 ( 11 ): 238 - 239 .
李书培 , 孙冬明 , 张赛 , 等 . 某机载光电系统风冷散热翅片优化设计及仿真 [J ] . 激光与红外 , 2024 , 54 ( 6 ): 951 - 957 .
Li S P , Sun D M , Zhang S , et al . Optimized design and simulation of air cooled heat dissipation fines for an airborne optoelectronic system [J ] . Laser & Infrared , 2024 , 54 ( 6 ): 951 - 957 .
Lu Z B , Li Y M , He C , et al . Multi-objective inverse design of finned heat sink system with physics-informed neural networks [J ] . Computers & Chemical Engineering , 2024 , 180 : 108500 .
Sun P Q , Ismail M A , Mustaffa A F . Metamodel-based design optimization for heat transfer enhancement of finned heat sinks [J ] . International Journal of Thermal Sciences , 2025 , 214 : 109896 .
Dong C C , Zhang C B , He G N , et al . Study on bionic leaf-vein like heat sinks topology optimisation method [J ] . Energy , 2025 , 319 : 135027 .
Yang Z P , He S P , Yu J C , et al . A machine learning-based generative design approach for rapid topology optimization of microchannel heat sinks [J ] . International Communications in Heat and Mass Transfer , 2025 , 169 : 109655 .
Lampio K , Karvinen R . A new method to optimize natural convection heat sinks [J ] . Heat and Mass Transfer , 2018 , 54 ( 8 ): 2571 - 2580 .
谢伟伟 . 基于热管原理的大功率LED灯散热器的设计与优化 [D ] . 南宁 : 广西大学 , 2022 .
Xie W W . Design and optimization of heat sink for high power led lamp based on heat pipe principle [D ] . Nanning : Guangxi University , 2022 .
高杰 , 樊凤昕 , 马丹竹 , 等 . 基于TEC和平板热管的LED散热器结构优化设计 [J ] . 电子与封装 , 2024 , 24 ( 5 ): 29 - 36 .
Gao J , Fan F X , Ma D Z , et al . Optimized design of LED radiator structure based on TEC and flat-plate heat pipe [J ] . Electronics & Packaging , 2024 , 24 ( 5 ): 29 - 36 .
Shehzad A , Dong C C , He G N , et al . Multi-objective topology optimization of microchannel cold plates for nuclear thermal management [J ] . Applied Thermal Engineering , 2026 , 302 : 131829 .
Cartis C , Massart E , Otemissov A . Bound-constrained global optimization of functions with low effective dimensionality using multiple random embeddings [J ] . Mathematical Programming , 2023 , 198 ( 1 ): 997 - 1058 .
Gamot J , Balesdent M , Tremolet A , et al . Hidden-variables genetic algorithm for variable-size design space optimal layout problems with application to aerospace vehicles [J ] . Engineering Applications of Artificial Intelligence , 2023 , 121 : 105941 .
Yu M J , Wang Z , Dai R , et al . A two-stage dominance-based surrogate-assisted evolution algorithm for high-dimensional expensive multi-objective optimization [J ] . Scientific Reports , 2023 , 13 : 13163 .
Shen J T , Wang X J , He R X , et al . Optimization of high-dimensional expensive multi-objective problems using multi-mode radial basis functions [J ] . Complex & Intelligent Systems , 2025 , 11 ( 2 ): 147 .
Zhou M C , Cui M J , Xu D , et al . Evolutionary optimization methods for high-dimensional expensive problems: a survey [J ] . IEEE/CAA Journal of Automatica Sinica , 2024 , 11 ( 5 ): 1092 - 1105 .
Meng X R , Zhu J , Wei X L , et al . Natural convection heat transfer of a straight-fin heat sink [J ] . International Journal of Heat and Mass Transfer , 2018 , 123 : 561 - 568 .
杨世铭 , 陶文铨 . 传热学 [M ] . 4版 . 北京 : 高等教育出版社 , 2006 : 263 - 277 .
Yang S M , Tao W Q . Heat transfer [M ] . 4th ed . Beijing : Higher Education Press , 2006 : 263 - 277 .
Khalafallah A , Hyari K H . Optimization parameter variation: improving biobjective optimization of temporary facility planning [J ] . Journal of Computing in Civil Engineering , 2018 , 32 ( 5 ): 04018036 .
0
浏览量
16
下载量
0
CSCD
关联资源
相关文章
相关作者
相关机构
京公网安备11010102001995号