翅片结构对2 K超流氦板翅式换热器流动换热的影响

李翠; 夏程萍; 刘睿奇; 厉彦忠

doi:10.11949/0438-1157.20260243

您当前的位置：

首页 >

文章列表页 >

翅片结构对2 K超流氦板翅式换热器流动换热的影响

专辑：低温科学与技术进展 | 更新时间：2026-06-09

- 翅片结构对2 K超流氦板翅式换热器流动换热的影响
- Effect of fin structure on flow and heat transfer characteristics of a 2 K superfluid helium plate-fin heat exchanger
- 化工学报 2026年
- 作者机构：
  
  西安交通大学能源与动力工程学院，陕西西安 710049
- 作者简介：
  
  李翠（1982—），女，博士，副教授，xjtucli@xjtu.edu.cn
- 基金信息：
  
  国家自然科学基金项目(52576021)
- DOI：10.11949/0438-1157.20260243
  中图分类号： TQ051.5;TB66
- 收稿：2026-02-18，
  
  修回：2026-06-08，
  
  录用：2026-06-09，
- 稿件说明：
移动端阅览
李翠, 夏程萍, 刘睿奇, 等. 翅片结构对2 K超流氦板翅式换热器流动换热的影响[J/OL]. 化工学报, 2026.

LI Cui, XIA Chengping, LIU Ruiqi, et al. Effect of fin structure on flow and heat transfer characteristics of a 2 K superfluid helium plate-fin heat exchanger[J/OL]. CIESC Journal, 2026.
李翠, 夏程萍, 刘睿奇, 等. 翅片结构对2 K超流氦板翅式换热器流动换热的影响[J/OL]. 化工学报, 2026. DOI： 10.11949/0438-1157.20260243.

LI Cui, XIA Chengping, LIU Ruiqi, et al. Effect of fin structure on flow and heat transfer characteristics of a 2 K superfluid helium plate-fin heat exchanger[J/OL]. CIESC Journal, 2026. DOI： 10.11949/0438-1157.20260243.

摘要

为探究2 K超流氦温区流动不均匀性对板翅式换热器性能的影响，采用数值模拟方法建立全尺寸三维模型，引入多孔介质方法并考虑氦的变物性，系统研究了冷热耦合、翅片节距及类型对流量分配与换热的影响。结果表明：冷热耦合效应使低压侧流动不均匀度较非耦合工况降低67.6%；锯齿翅片节距为10 mm时均匀性最优，换热效率随节距减小而增大，压降亦显著上升；锯齿翅片换热效率最高但压降最大，打孔翅片压降最小。综合考虑出口压降低于100 Pa的工程要求，建议优先选用打孔翅片或大节距锯齿翅片。研究结果为大型超流氦低温系统优化设计提供理论依据。

Abstract

As a critical component in large-scale particle colliders' superfluid helium cryogenic systems

the 2 K negative-pressure plate-fin heat exchanger directly determines overall operational efficiency. To elucidate the effects of flow maldistribution on the performance of plate-fin heat exchangers within the superfluid helium temperature regime

this study employs numerical simulation techniques. A full-scale three-dimensional model of a plate-fin heat exchanger is developed integrating the porous media approach

while accounting for the variations in helium’s thermophysical properties across the 2 K–4.5 K range. Systematic investigations are conducted to evaluate the impacts of thermal-hydraulic coupling

fin pitch

and fin type on flow distribution and heat transfer characteristics. Results indicate that the thermal-hydraulic coupling effect substantially enhances flow uniformity through a temperature-density-resistance feedback mechanism

reducing the flow maldistribution index on the low-pressure side by 67.6% relative to the non-coupled condition. Fin pitch exerts a significant influence on flow distribution

with optimal uniformity observed at a pitch of 10 mm. Heat transfer efficiency increases with decreasing fin pitch

albeit accompanied by a marked elevation in pressure drop. Among the fin types examined

the serrated fin achieves the highest heat transfer efficiency but incurs the largest pressure drop

the perforated fin exhibits the minimum pressure drop yet lower heat transfer efficiency

and the wavy fin demonstrates intermediate performance. Considering the engineering constraint of an outlet pressure drop below 100 Pa for superfluid helium cryogenic systems

the perforated fin or serrated fin with a larger pitch is recommended to achieve favorable heat transfer performance while meeting the pressure drop requirement. These findings offer a theoretical foundation for the efficient operation and optimal design of large-scale superfluid helium cryogenic systems.

关键词

Keywords

references

唐琳 . 我国研发成功-271℃超流氦大型低温制冷装备 [J ] . 科学新闻 , 2022 , 24 ( 3 ): 23 .

Tang L . China has successfully developed a large-scale cryogenic refrigeration equipment with-271℃ superfluid helium [J ] . Science News , 2022 , 24 ( 3 ): 23 .

Bradu B , Brodzinski K , Gahier V , et al . LHC low-beta quadrupole magnets: cryogenic refrigeration capacity and improved controls for luminosity optimization [J ] . Journal of Physics: Conference Series , 2024 , 2687 ( 8 ): 082023 .

唐景春 , 贾帅 , 陈长琦 , 等 . 超流氦系统中2～4 K负压换热器换热性能的数值模拟 [J ] . 合肥工业大学学报(自然科学版) , 2021 , 44 ( 12 ): 1598 - 1603 .

Tang J C , Jia S , Chen C Q , et al . Numerical simulation of heat transfer performance of 2-4 K sub-atmospheric heat exchanger in superfluid helium cryogenic system [J ] . Journal of Hefei University of Technology (Natural Science) , 2021 , 44 ( 12 ): 1598 - 1603 .

任志文 , 黄桂朝 , 刘具龙 , 等 . 超大型负压低温换热器的热工特性分析 [J ] . 真空与低温 , 2025 , 31 ( 1 ): 98 - 103 .

Ren Z W , Huang G C , Liu J L , et al . Analysis of thermal characteristics of ultra-large negative pressure cryogenic heat exchangers [J ] . Vacuum and Cryogenics , 2025 , 31 ( 1 ): 98 - 103 .

王哲 , 厉彦忠 , 李正宇 , 等 . 液氦/超流氦制冷系统负压换热器仿真及优化设计 [J ] . 西安交通大学学报 , 2016 , 50 ( 8 ): 143 - 150 .

Wang Z , Li Y Z , Li Z Y , et al . Simulation and optimization for sub-atmospheric heat exchanger of liquid helium/superfluid helium refrigeration system [J ] . Journal of Xi'an Jiaotong University , 2016 , 50 ( 8 ): 143 - 150 .

Zhu K Y , Chang Z Z , Li M , et al . Design, optimization and experimental testing of 2 K cryogenic plate-fin heat exchanger [J ] . Applied Thermal Engineering , 2023 , 223 : 119973 .

Wen J , Li C L , Hao H W , et al . Numerical investigation on fin configuration improvement of 2 K sub-atmospheric plate-fin heat exchangers for the superfluid helium cryogenic systems [J ] . Applied Thermal Engineering , 2021 , 196 : 117290 .

朱黎明 , 范大军 , 王先进 , 等 . 超流氦低温系统板式换热器的设计与优化 [J ] . 真空与低温 , 2023 , 29 ( 5 ): 511 - 517 .

Zhu L M , Fan D J , Wang X J , et al . Design and optimization of plate heat exchanger for the superfluid helium cryogenic system [J ] . Vacuum and Cryogenics , 2023 , 29 ( 5 ): 511 - 517 .

李超龙 , 许世峰 , 文键 , 等 . 负压低温板翅式换热器锯齿翅片性能的数值模拟研究 [J ] . 真空与低温 , 2021 , 27 ( 2 ): 141 - 145, 177 .

Li C L , Xu S F , Wen J , et al . Numerical simulation of serrated fin performance of plate fin heat exchanger under negative pressure and low temperature condition [J ] . Vacuum and Cryogenics , 2021 , 27 ( 2 ): 141 - 145, 177 .

朱柯宇 , 常正则 , 李梅 , 等 . 千瓦级2 K超流氦板翅式换热器初步设计优化 [J ] . 原子能科学技术 , 2022 , 56 ( 10 ): 2146 - 2154 .

Zhu K Y , Chang Z Z , Li M , et al . Preliminary design optimization of 2 K superfluid helium plate-fin heat exchanger in kilowatt scale [J ] . Atomic Energy Science and Technology , 2022 , 56 ( 10 ): 2146 - 2154 .

郝鸿伟 , 文键 , 赵欣 , 等 . 超流氦系统负压低温板翅式换热器新型波纹-锯齿翅片的性能研究 [J ] . 西安交通大学学报 , 2021 , 55 ( 11 ): 1 - 7 .

Hao H W , Wen J , Zhao X , et al . Study on the performance of a new-type sine-offset fin for negative pressure low temperature plate-fin heat exchanger in superfluid helium system [J ] . Journal of Xi’an Jiaotong University , 2021 , 55 ( 11 ): 1 - 7 .

刘轶伦 , 何崇超 , 丁培 , 等 . 超流氦负压换热器设计与数值模拟研究 [J ] . 低温工程 , 2025 ( 1 ): 70 - 77, 86 .

Liu Y L , He C C , Ding P , et al . Design and numerical simulation of superfluid helium sub-atmospheric heat exchanger [J ] . Cryogenics , 2025 ( 1 ): 70 - 77, 86 .

文键 , 厉彦忠 , 周爱民 , 等 . 板翅式换热器入口结构的改进 [J ] . 吉林大学学报(工学版) , 2006 , 36 ( 2 ): 177 - 182 .

Wen J , Li Y Z , Zhou A M , et al . Improvement of entrance configuration in plate-fin heat exchanger [J ] . Journal of Jilin University (Engineering and Technology Edition) , 2006 , 36 ( 2 ): 177 - 182 .

王少华 , 文键 , 李亚梅 , 等 . 带有导流翼的板翅式换热器封头结构优化研究 [J ] . 化学工程 , 2013 , 41 ( 7 ): 24 - 28 .

Wang S H , Wen J , Li Y M , et al . Configuration optimization of wing panel header in plate-fin heat exchanger [J ] . Chemical Engineering , 2013 , 41 ( 7 ): 24 - 28 .

Yang H Z , Wen J , Gu X , et al . Improvements on flow distribution and heat transfer performance of plate-fin heat exchangers by qusai-S type header configuration [J ] . Heat Transfer Engineering , 2017 , 38 ( 18 ): 1547 - 1560 .

李登洪 . 板翅式换热器封头与翅片结构优化及性能协调设计 [D ] . 杭州 : 浙江工业大学 , 2020 .

Li D H . Structure optimization and performance coordination design of inlet header and fin in plate-fin heat exchanger [D ] . Hangzhou : Zhejiang University of Technology , 2020 .

辛杰 , 唐凌虹 , 刘佳伦 , 等 . 板翅式换热器内气液两相流分配特性数值分析 [J ] . 机电工程技术 , 2024 , 53 ( 4 ): 222 - 226 .

Xin J , Tang L H , Liu J L , et al . Study on distribution characteristics of gas-liquid two-phase flow in plate-fin heat exchanger [J ] . Mechanical & Electrical Engineering Technology , 2024 , 53 ( 4 ): 222 - 226 .

彭翔 , 高启龙 . 面向封头流动不均匀性的板翅式换热器通道布局优化设计 [J ] . 化工机械 , 2021 , 48 ( 2 ): 268 - 273, 282 .

Peng X , Gao Q L . Optimal design of passage arrangement for plate-fin heat exchanger with inlet flow maldistribution in header [J ] . Chemical Engineering & Machinery , 2021 , 48 ( 2 ): 268 - 273, 282 .

曹学文 , 石倩 , 彭文山 . 板翅式换热器结构优化及其性能数值模拟 [J ] . 油气储运 , 2019 , 38 ( 9 ): 1048 - 1053 .

Cao X W , Shi Q , Peng W S . Structure optimization and performance numerical simulation of plate-fin heat exchanger [J ] . Oil & Gas Storage and Transportation , 2019 , 38 ( 9 ): 1048 - 1053 .

Tang Z C , He S , Li N Q , et al . Non-equilibrium overlapping grid method with two-phase porous media model for printed circuit heat exchanger based steam generator [J ] . International Journal of Heat and Mass Transfer , 2024 , 232 : 125960 .

Du J , Zhao H T . Numerical simulation of a plate-fin heat exchanger with offset fins using porous media approach [J ] . Heat and Mass Transfer , 2018 , 54 ( 3 ): 745 - 755 .

Du J , Deng J . Heat transfer enhancement using non-equally structure in a plate-fin heat exchanger with offset fins [J ] . Thermal Science , 2022 , 26 ( 6 part B ): 4919 - 4930 .

谯厚峰 , 蔡彧青 , 杜昶 , 等 . 基于多孔介质模型的翅片换热器性能预测 [J ] . 低温与超导 , 2025 , 53 ( 8 ): 1 - 6 .

Qiao H F , Cai Y Q , Du C , et al . Performance prediction of fin heat exchanger based on porous medium model [J ] . Cryogenics & Superconductivity , 2025 , 53 ( 8 ): 1 - 6 .

李淑铭 . 基于多孔介质方法的板翅式换热器流动传热特性模拟研究 [D ] . 广州 : 广东工业大学 , 2024 .

Li S M . Simulation study on flow heat transfer characteristics of plate-fin heat exchanger based on porous media approach [D ] . Guangzhou : Guangdong University of Technology , 2024 .

张冰 . 板翅式换热器封头内流体分配特性及结构优化研究 [D ] . 杭州 : 浙江大学 , 2017 .

Zhang B . Study on flow distribution characteristics in head of plate fin heat exchanger and structural optimization [D ] . Hangzhou : Zhejiang University , 2017 .

余建祖 . 换热器原理与设计 [M ] . 北京 : 北京航空航天大学出版社 , 2006 .

Yu J Z . Principle and design of heat exchanger [M ] . Beijing : Beijing University of Aeronautics & Astronautics Press , 2006 .

李翠 , 夏程萍 , 刘睿奇 , 等 . 氦负压板翅式换热器的流动不均匀性 [J ] . 化工进展 , 2026 , 45 ( 1 ): 40 - 49 .

Li C , Xia C P , Liu R Q , et al . Flow maldistribution in sub-atmospheric plate-fin heat exchangers with helium [J ] . Chemical Industry and Engineering Progress , 2026 , 45 ( 1 ): 40 - 49 .

李翠 , 刘睿奇 , 朱柯宇 , 等 . 千瓦级2K负压板翅式换热器性能研究 [J ] . 中南大学学报(自然科学版) , 2025 , 56 ( 10 ): 4411 - 4423 .

Li C , Liu R Q , Zhu K Y , et al . Performance study of kilowatt-class 2K sub-atmospheric plate-fin heat exchanger [J ] . Journal of Central South University (Science and Technology) , 2025 , 56 ( 10 ): 4411 - 4423 .

邹中宇 , 张启勇 , 朱志刚 , 等 . 锯齿型翅片内不同温区氦气流动与传热性能对比及节距对翅片性能影响的研究 [J ] . 真空与低温 , 2024 , 30 ( 3 ): 274 - 281 .

Zou Z Y , Zhang Q Y , Zhu Z G , et al . Numerical investigation on heat transfer and flow performances of helium gas in serrated fins channels [J ] . Vacuum and Cryogenics , 2024 , 30 ( 3 ): 274 - 281 .

浏览量

下载量

CSCD

文章被引用时，请邮件提醒。

提交

工具集

关联资源

不同SK型静态混合器的流场特性及其混合效果分析

带有突扩比的新型流道结构对海水激活电池性能的影响

Ca（OH）2/CaO间接反应器储释热循环性能优化

液氢贮箱在轨排气的闪蒸特性与热力态调节规律研究

桨形螺杆元件开发及其柔性混合能力分析