Numerical simulation and experimental validation of water condensing and moving on plain-fin surface under dehumidifying conditions

YANG Yifei; ZHUANG Dawei; HU Haitao; HAN Weizhe; DING Guoliang; XIONG Wei

doi:10.3969/j.issn.0438-1157.2014.z2.021

您当前的位置：

首页 >

文章列表页 >

Numerical simulation and experimental validation of water condensing and moving on plain-fin surface under dehumidifying conditions

更新时间：2025-12-10

- Numerical simulation and experimental validation of water condensing and moving on plain-fin surface under dehumidifying conditions
- CIESC Journal Issue z2, Pages: 140-147(2014)
- 作者机构：
  
  上海交通大学制冷与低温工程研究所,上海,200240
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.z2.021
  CLC： K124
- Online First：30 December 2014，
  
  Published：30 December 2014
- 稿件说明：
移动端阅览
YANG Yifei, ZHUANG Dawei, HU Haitao, et al. Numerical simulation and experimental validation of water condensing and moving on plain-fin surface under dehumidifying conditions[J]. CIESC Journal, 2014, (z2): 140-147.
DOI：

YANG Yifei, ZHUANG Dawei, HU Haitao, et al. Numerical simulation and experimental validation of water condensing and moving on plain-fin surface under dehumidifying conditions[J]. CIESC Journal, 2014, (z2): 140-147. DOI： 10.3969/j.issn.0438-1157.2014.z2.021.

摘要

了解析湿过程中冷凝水对换热器翅片侧换热和压降的影响机制

需要首先建立湿工况下翅片表面冷凝水滴形成及运动过程的模型。本文通过对翅片表面上冷凝水滴的形成和运动机制进行分析

建立水滴形成过程的传质传热模型以及接触角模型

并结合VOF界面追踪方法来描述气液相界面、计算表面张力

从而预测冷凝水滴在竖直翅片表面形成及运动过程。通过实验对模型的可靠性进行了验证:对于传热系数

模型计算结果与实验数据平均误差为6.9%

模型对于96%的实验数据点预测误差在±15%以内;对于传质系数

模型计算结果与实验平均误差为12.1%

模型对于91%的实验数据点预测误差在±20%以内;对于翅片表面水滴形成和运动过程

模型计算结果与可视化实验结果能够较好地吻合。

Abstract

In order to predict the performance of tube-finned heat exchangers under dehumidifying condition

the behavior of condensing liquid droplet on vertical plain-fin surfaces should be known. The objective of this article is to develop a model for liquid droplet condensation and motion on vertical plain-fin surfaces. To achieve this goal

the mechanisms of droplet condensation and motion are analyzed firstly. Then the equations for predicting the heat and mass transfer rate during the water condensation are established

and a Volume of Fluid-Continuous Surface Force model with varying contact angles along the contact line is developed to predict droplet movement. The prediction ability was verified by the experimental data

and verification results show that: the simulation results of jh agree with 96% of the experimental data within the deviation of ±15%

and the mean deviation is 6.9%; the simulation results of jm agree with 91% of the experimental data within the deviation of ±20%

and the mean deviation is 12.1%.

关键词

Keywords

references

Views

360

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Experimental study of particle motion and heat transfer in externally heated rotary kiln

Numerical simulation for flow condensation of methanol in horizontal tube

Experimental study on condensation heat transfer of R134a in mini channel with micro diamond fins

Numerical study on non-equilibrium condensation and flashing mechanisms in rapid expansion process of transcritical CO2

Experimental study on condensation heat transfer characteristics of low mass flow rate steam in a vacuum horizontal tube

Related Author

MA Chi

XU Huibin

LI Xunxin

WANG Weiyu

PENG Feizi

HU Haitao

CHANG Shoujin

GUO Jiangyue

Related Institution

Jiangsu Engineering Research Center for Intelligent Equipment of Advanced Powder Materials Handling

School of Energy and Power Engineering, Jiangsu University

School of Mechanical Engineering, Shanghai Jiao Tong University

Key Laboratory of Aviation Electromechanical Integration Technology

Institute of Air Conditioning and Refrigeration, Key Laboratory of Aircraft Environment Control and Life Support, Nanjing University of Aeronautics and Astronautics

⁰