Analysis on structural stress of tube in steam generator based on fluid-structure interaction

SUN Baozhi; ZHENG Lusong; HAN Wenjing; ZHANG Guolei; LIU Shanghua

doi:10.3969/j.issn.0438-1157.2014.z1.059

您当前的位置：

首页 >

文章列表页 >

Analysis on structural stress of tube in steam generator based on fluid-structure interaction

更新时间：2025-12-10

- Analysis on structural stress of tube in steam generator based on fluid-structure interaction
- CIESC Journal Issue S1, Pages: 364-370(2014)
- 作者机构：
  
  哈尔滨工程大学动力与能源工程学院,黑龙江,哈尔滨,150001
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.z1.059
  CLC： Q028.8
- Online First：30 May 2014，
  
  Published：30 May 2014
- 稿件说明：
移动端阅览
SUN Baozhi, ZHENG Lusong, HAN Wenjing, et al. Analysis on structural stress of tube in steam generator based on fluid-structure interaction[J]. CIESC Journal, 2014, (S1): 364-370.
DOI：

SUN Baozhi, ZHENG Lusong, HAN Wenjing, et al. Analysis on structural stress of tube in steam generator based on fluid-structure interaction[J]. CIESC Journal, 2014, (S1): 364-370. DOI： 10.3969/j.issn.0438-1157.2014.z1.059.

摘要

以核电站蒸汽发生器为研究对象，采用两流体模型描述二次侧汽液两相流动及沸腾换热，利用CFX对一、二次侧流体与换热管及支撑板的耦合流动换热进行三维数值模拟，在此基础上提取一、二次侧流体压力载荷，在Workbench平台中实现载荷向结构模型的传递，计算换热管结构应力。流固耦合计算结果表明：支撑板位置处二次侧流体流速迅速增大又快速减小，并且流体湍流耗散急剧增大造成二次侧流体压力损失增大；换热管压力应力取决于一、二次侧流体压差，整体平均压力应力约为58 MPa，与实际测量参数相符。

Abstract

Taken the steam generator of nuclear power plant as the prototype

the vapor-liquid two-phase flow and the boiling heat transfer were simulated by two-fluid model. The coupled flow and heat transfer process between the fluid of the primary and secondary sides and the heat transfer tubes with support plates was numerically simulated using CFX software. Based on the flow and heat transfer calculation

the pressure of fluid in the primary and secondary sides was extracted. The pressure load was transferred to the structure model in Workbench. And the structural stress of tube was calculated. The fluid-structure interaction results show that there is an abrupt increase in secondary velocity at the positions of support plates. The fluid pressure loss of secondary side increases because of the increase of fluid turbulence dissipation. The pressure stress of the heat transfer tube depends on the pressure difference between the primary side and the secondary side. The overall average of the pressure stress is about 58 MPa

which is consistent with the actual measured parameter.

关键词

Keywords

references

Views

389

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Investigation of bubble behaviors in gas-liquid two-phase flow in helically coiled tube based on wire mesh sensor

Experimental study and CFD simulation of heat transfer in polymerization reactor

Solid-liquid suspension behavior intensified by punched rigid-flexible impeller

Prediction of two-phase pressure drop under different operating parameters for once-through steam generator

Dynamic characteristics of impeller of perturbed six-bent-bladed turbine in pseudoplastic fluid based on fluid-structure interaction

Related Author

WANG Ke

DAI Juntao

LIU Li

LIU Shuai

GU Hanyang

Yufan WU

Luyang GUO

Qinghua LU

Related Institution

College of Mechanical and Transportation Engineering, China University of Petroleum

School of Nuclear Science and Engineering, Shanghai Jiao Tong University

Shanghai Key Laboratory of Catalysis Technology for Polyolefins, Shanghai Research Institute of Chemical Industry Co., Ltd.

School of Chemistry and Chemical Engineering, Shanghai Jiao Tong University

State Key Laboratory of Polyolefins and Catalysis, Shanghai Research Institute of Chemical Industry Co., Ltd.

⁰