Numerical simulations of impinging heat transfer characteristics for multi-pulsating jets with phase difference

GENG Liping; XU Qinggong; ZHENG Chuanbo; ZHOU Jingwei

doi:10.3969/j.issn.0438-1157.2014.z1.039

您当前的位置：

首页 >

文章列表页 >

Numerical simulations of impinging heat transfer characteristics for multi-pulsating jets with phase difference

更新时间：2025-12-10

- Numerical simulations of impinging heat transfer characteristics for multi-pulsating jets with phase difference
- CIESC Journal Issue S1, Pages: 240-244(2014)
- 作者机构：
  
  1. 中国计量学院热能工程系,浙江,杭州,310018
  2. 洛阳理工学院计算机与信息工程系,河南,洛阳,471023
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.z1.039
  CLC： K124
- Online First：30 May 2014，
  
  Published：30 May 2014
- 稿件说明：
移动端阅览
GENG Liping, XU Qinggong, ZHENG Chuanbo, et al. Numerical simulations of impinging heat transfer characteristics for multi-pulsating jets with phase difference[J]. CIESC Journal, 2014, (S1): 240-244.
DOI：

GENG Liping, XU Qinggong, ZHENG Chuanbo, et al. Numerical simulations of impinging heat transfer characteristics for multi-pulsating jets with phase difference[J]. CIESC Journal, 2014, (S1): 240-244. DOI： 10.3969/j.issn.0438-1157.2014.z1.039.

摘要

采用数值模拟的方法对带相差的多喷嘴射流冲击传热进行数值模拟，分别得到不同相差和不同射流频率条件下的冲击传热效果。结果显示，在不同的射流喷射模式下，按相差顺序增加方式（B型）喷出的射流传热效果最好，两喷嘴间的相差为0°～180°之间时，传热板的传热效果随着相差角度的增加，传热效果得到增强，且在相差为120°时，整个传热板传热效果最均匀；在频率为0～10Hz时，频率越大，整个传热板传热越均匀，但频率的影响小于相差及喷射模式的影响。

Abstract

A series of numerical simulations for multi-pulsating jets with phase difference are carried out in order to obtain impinging heat transfer characteristics. The results are compared with changed phase difference in jet modes and values and pulse frequency. Jet modes include the symmetrically increasing phase difference (mode A)

the gradually increasing phase difference (mode B) and alternative phase difference (mode C). It can be found that mode B with gradually increasing phase mode has the best heat transfer characteristics within this research scope. When the phase difference lies between 0°-180°

the heat transfer characteristics become stronger with the increase of phase difference. When the phase difference is 120°

the heat transfer characteristics are best-distributed on the whole plate. Such well-distribution of heat transfer is also influenced by frequency. And the heat transfer characteristics are better-distributed when the frequency increase in the range of 0-10Hz. However

the influence of frequency is less than those of phase difference in jet modes and values.

关键词

Keywords

references

Views

317

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of height of winglet vortex generators on thermal hydrodynamic performance of tube bank fin heat exchanger

Application of exergy destruction minimization in convective heat transfer optimization for elliptical tube

Numerical simulation of coupled heat transfer for LNG pipeline

Containment system of new independent type B LNG carrier and boil off rate calculation

The impact of novel flow channel structure with sudden-expansion ratio on seawater-activated battery

Related Author

HU Wanling

WANG Liangbi

WANG Junbo

XIE Pan

LIU Zhichun

LIU Wei

HU Zhuohuan

HUANG Tianke

Related Institution

School of Environmental and Municipal Engineering, Lanzhou Jiaotong University

School of Mechanical Engineering, Lanzhou Jiaotong University

School of Energy and Power Engineering, Huazhong University of Science and Technology

School of Energy and Power Engineering, University of Shanghai for Science and Technology

Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University

⁰