Experimental study and numerical simulation on jet streaming in deep bubbling fluidized-bed

YAN Shuren; LIANG Yongshi; ZHANG Yongmin

doi:10.3969/j.issn.0438-1157.2014.12.018

您当前的位置：

首页 >

文章列表页 >

Experimental study and numerical simulation on jet streaming in deep bubbling fluidized-bed

更新时间：2025-12-10

- Experimental study and numerical simulation on jet streaming in deep bubbling fluidized-bed
- CIESC Journal Issue 12, Pages: 4775-4784(2014)
- 作者机构：
  
  中国石油大学(北京)重质油国家重点实验室,北京,102249
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.12.018
  CLC： F803.11
- Online First：05 December 2014，
  
  Published：05 December 2014
- 稿件说明：
移动端阅览
YAN Shuren, LIANG Yongshi, ZHANG Yongmin. Experimental study and numerical simulation on jet streaming in deep bubbling fluidized-bed[J]. CIESC Journal, 2014, (12): 4775-4784.
DOI：

YAN Shuren, LIANG Yongshi, ZHANG Yongmin. Experimental study and numerical simulation on jet streaming in deep bubbling fluidized-bed[J]. CIESC Journal, 2014, (12): 4775-4784. DOI： 10.3969/j.issn.0438-1157.2014.12.018.

摘要

针对催化裂化空筒汽提器中存在的气体偏涌现象

在一套大型空筒催化剂汽提器冷模实验装置中利用光纤探针法系统研究了偏涌的特性及其随床层高度的发展变化情况

并进一步利用一种新的离散颗粒计算流体力学模型(CPFD模型)对该现象进行了数值模拟研究.结果表明

在催化裂化汽提器操作条件下

偏涌主要发生在临近床层边壁的位置

造成周向上颗粒浓度分布呈现严重的不均匀性

偏涌的强度会随着床层高度的增大而减弱.CPFD模型不仅能够成功预测深层鼓泡床中存在的偏涌现象

而且可以定性预测偏涌强度沿床层高度的发展趋势

但定量预测结果较实验结果偏大.上述结果对工业汽提器的设计和故障诊断具有指导意义.

Abstract

By means of optical fiber probe

the jet streaming phenomenon in FCC baffle-free strippers was studied in a large cold-model experimental unit. Its properties as well as its development with bed height were studied. A newly developed computational particle fluid dynamics (CPFD) model was further used to explore this phenomenon. Jet streaming mainly happened near the stripper wall

resulting in serious non-uniformity in circumferential solids distribution. The strength of jet streaming decreased with increasing bed height. CPFD model could successfully predict the existence of jet streaming in this system. Although the predicted jet streaming strengths at higher bed heights were slightly overestimated

its trend with increasing bed height qualitatively agreed with the experimental fact. The deeper understanding acquired in this study can be used as a good reference for design and troubleshooting of the industrial FCC strippers.

关键词

Keywords

references

Views

201

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Study on orthohydrogen and parahydrogen conversion coupled flow and heat transfer based on helium expansion refrigeration

Direct numerical simulation of restitution coefficient during oblique collision of wet particles

Review of numerical study on liquid-solids two-phase mass transfer process in fluidized bed

Numerical simulation research of high-alkali coal ash deposition process based on discrete element method

Establishment of bubble-based EMMS/PFB model and its application on dense section of pressurized fluidized-bed

Related Author

LIU Lu

WAN Kai

WANG Wenyue

WANG Tai

TANG Jiancheng

WANG Shaoheng

LIU Daoyin

FAN Zhiheng

Related Institution

Hebei Key Laboratory of Low Carbon and High Efficiency Power Generation Technology

Department of Power Engineering, North China Electric Power University

Beijing Da Zhen Technology Co., Ltd.

Hebei Kude Refrigeration Technology Co., Ltd.

Key Laboratory of Energy Thermal Conversion and Control of Ministry of Education, School of Energy and Environment, Southeast University

⁰