Optimization of ethyl acetate process conditions for sodium bisulfate fluidized catalytic distillation using response surface methodology

XIAO Wu; LI Mingyue; RUAN Xuehua; HE Gaohong; DU Jian

doi:10.3969/j.issn.0438-1157.2014.11.035

您当前的位置：

首页 >

文章列表页 >

Optimization of ethyl acetate process conditions for sodium bisulfate fluidized catalytic distillation using response surface methodology

更新时间：2025-12-10

- Optimization of ethyl acetate process conditions for sodium bisulfate fluidized catalytic distillation using response surface methodology
- CIESC Journal Issue 11, Pages: 4465-4471(2014)
- 作者机构：
  
  大连理工大学化工学院, 精细化工国家重点实验室, 膜科学与技术研究开发中心,辽宁,大连,116024
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.11.035
  CLC： Q225.24
- Online First：05 November 2014，
  
  Published：05 November 2014
- 稿件说明：
移动端阅览
XIAO Wu, LI Mingyue, RUAN Xuehua, et al. Optimization of ethyl acetate process conditions for sodium bisulfate fluidized catalytic distillation using response surface methodology[J]. CIESC Journal, 2014, (11): 4465-4471.
DOI：

XIAO Wu, LI Mingyue, RUAN Xuehua, et al. Optimization of ethyl acetate process conditions for sodium bisulfate fluidized catalytic distillation using response surface methodology[J]. CIESC Journal, 2014, (11): 4465-4471. DOI： 10.3969/j.issn.0438-1157.2014.11.035.

摘要

以新型的一水硫酸氢钠为催化剂

采用粉末状催化剂混合乙酸一起进料的加入方式

即流化催化精馏工艺

并利用响应面法优化乙酸乙酯催化精馏过程条件.首先

通过单因素灵敏度分析法对乙酸进料量、酸醇进料摩尔比、回流比、催化剂用量、釜底加热功率5个因素进行实验考察

确定了乙酸进料量、酸醇摩尔进料比、回流比3个关键因素的优化值及取值范围.根据单因素实验结果与精馏塔设备要求

塔釜加热功率和催化剂用量分别设定为68 W和2.0%(质量分数)乙酸

采用中心组合设计原则对乙酸进料量、酸醇进料摩尔比和回流比3个关键因素进行实验设计.以乙醇转化率为响应值

基于响应实验结果

利用响应面法对实验结果进行了方程回归

得到3个关键因素与响应值的二次关联模型.通过方差分析和平行实验

证明该模型准确可用.优化后的乙酸乙酯流态化催化精馏工艺条件为乙酸进料量3.2 mol·h-1

酸醇进料摩尔比为3.1

回流比为3.3

在此优化条件下进行实验

乙醇转化率为88.67%

比基于单因素灵敏度分析法得到的优化工艺条件下乙醇转化率高1.0%.

Abstract

A novel fluidized catalytic distillation process was developed to produce ethyl acetate based on sodium bisulfate catalyst

and response surface method was used to optimize process parameters. Firstly

single factor sensitivity analysis of five parameters

such as catalyst amount

reflux ratio

bottom heating power

acid alcohol molar feed ratio

feed rate

were carried out

and three key parameters (reflux ratio

acid alcohol molar feed ratio and feed rate) and their optimum ranges were determined. Depending on the results of single factor experiments and hydraulic limit of distillation equipment

reboiler duty of column 68 W and the amount of catalyst 2.0%(mass) acetic acid were fixed. Then central composite design methodology was used to design the experimental cases. The correlation model between three key parameters and the conversion rate of ethanol was obtained by response surface methodology based on the experimental results. By the analysis of variance and parallel experiments

the model was proved to be accurate and available. Finally

the optimum conditions were found to be feed flow of acetic acid 3.2 mol·h-1 and mole ratio of acetic acid/ethanol 3.1

reflux ratio 3.3. Under the conditions

the conversion rate of ethanol is 88.67%. Compared to the optimization parameters by a single factor sensitivity analysis process

the conversion rate of ethanol is increased by 1.0%.

关键词

Keywords

references

Views

332

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Multi-objective optimization of amine-based desulfurization regeneration system integrated with heat pump technology

Study on optimization of thermal-photovoltaic membrane distillation system based on response surface methodology

Preparation of LDHs-CRMA composite modified asphalt by response surface methodology and its characterization

Synthesis of polysulfone-based anion exchange membrane optimized by using response surface methodology

Preparation and characterization of nanoscale humic acid-urea complex under low temperature conditions

Related Author

LI Xuewen

WANG Zhihong

GAO Yang

WU Ming'ou

MA Wenhao

TAN Renmin

Qinyi ZHANG

Xiaohong YANG

Related Institution

School of Chemistry and Chemical Engineering, Southwest Petroleum University

Central Sichuan Oil & Gas Field, PetroChina Southwest Oil & Gasfield Company

Natural Gas Research Institute, PetroChina Southwest Oil & Gasfield Company

School of Energy and Power Engineering, Inner Mongolia University of Technology

Key Laboratory of Wind and Solar Energy Utilization Technology, Ministry of Education

⁰