Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores

CHENG Xiangping; MENG Xiangkai; PENG Xudong

doi:10.3969/j.issn.0438-1157.2014.08.033

您当前的位置：

首页 >

文章列表页 >

Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores

更新时间：2025-12-10

- Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores
- CIESC Journal Issue 8, Pages: 3089-3097(2014)
- 作者机构：
  
  1. 浙江工业大学机械工程学院,浙江,杭州,310032
  2. 浙江工业大学过程装备及其再制造教育部工程研究中心,浙江,杭州,310032
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.08.033
  CLC： H117.2
- Online First：05 August 2014，
  
  Published：05 August 2014
- 稿件说明：
移动端阅览
CHENG Xiangping, MENG Xiangkai, PENG Xudong. Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores[J]. CIESC Journal, 2014, (8): 3089-3097.
DOI：

CHENG Xiangping, MENG Xiangkai, PENG Xudong. Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores[J]. CIESC Journal, 2014, (8): 3089-3097. DOI： 10.3969/j.issn.0438-1157.2014.08.033.

摘要

针对等深大菱形孔端面液体润滑机械密封，采用有限差分法求解等温及层流不可压缩二维Reynolds方程，获得液膜压力场。利用商用有限元软件计算密封环三维固体变形，对不同操作工况条件下和不同结构的密封环的力变形、摩擦扭矩、液膜刚度及泄漏率等性能参数进行了计算。结果表明：大菱形孔流体动压型机械密封端面产生周向波度和径向锥度变形；改变工况条件可使密封面形成收敛和发散两种不同的变形，密封性能参数因此产生显著变化；当面积比B=0.65～0.75时，大菱形孔端面密封可获得较好的密封性能；辅助密封圈O形圈位置l对径向锥度变形具有很大影响，l优选值范围为2.4～4.0 mm。

Abstract

For a liquid lubricated end face mechanical seal with diamond macro-pores

the finite difference method was used to solve the two-dimension Reynolds equation for the isothermal

laminar and incompressible lubrication film and film pressure distribution was obtained. Finite element software was used to calculate surface deformation of seal rings. Deformation and seal performance parameters

such as friction torque

liquid film stiffness and leakage rate were investigated under different operating conditions for different sealing rings constructions. The results showed that the end face of mechanical seal deformed with circumferential waviness and radial coning. Convergent and divergent deformations occurred according to different operating conditions

hence seal performance greatly changed. When B was 0.65-0.75

the mechanical seal could achieve better sealing performance. The location of the secondary O ring greatly influenced radial taper deformation

the range of l preferred values was 2.4-4.0 mm.

关键词

Keywords

references

Views

277

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of irregular V-shaped surface texture on the performance of mechanical face seal

Comparative study on single-phase flow and heat transfer of different cross-section rib-soft tail structures

Analysis of flow and heat transfer characteristics of lubricating oil in circular tube with coaxial crossed vortex generators

Comparative analysis of laminar flow and heat transfer characteristics in a circular tube with different shape vortex generators

Research on the characterization of the molecular weight and its distribution of perfluoropolyether

Related Author

ZHAO Wenjing

TU Zhirong

MENG Xiangkai

JIANG Jinbo

PENG Xudong

Wenjing Zhao

Zhirong Tu

Xiangkai Meng

Related Institution

College of Mechanical Engineering, Zhejiang University of Technology

School of Energy and Power Engineering, Xi’an Jiaotong University

State Key Laboratory of HVDC, Electric Power Research Institute, China Southern Power Grid

School of Mechanical Engineering, Lanzhou Jiaotong University

Key Laboratory of Railway Vehicle Thermal Engineering, Ministry of Education

⁰