Comparison on seal performance of liquid-lubricated end face seals with different shapes inclined dimples

SHE Baoying; PENG Xudong; MENG Xiangkai; LI Jiyun

doi:10.3969/j.issn.0438-1157.2014.06.034

您当前的位置：

首页 >

文章列表页 >

Comparison on seal performance of liquid-lubricated end face seals with different shapes inclined dimples

更新时间：2025-12-10

- Comparison on seal performance of liquid-lubricated end face seals with different shapes inclined dimples
- CIESC Journal Issue 6, Pages: 2202-2210(2014)
- 作者机构：
  
  浙江工业大学过程装备及其再制造教育部工程研究中心,浙江,杭州,310032
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.06.034
  CLC： H117.2
- Online First：05 June 2014，
  
  Published：05 June 2014
- 稿件说明：
移动端阅览
SHE Baoying, PENG Xudong, MENG Xiangkai, et al. Comparison on seal performance of liquid-lubricated end face seals with different shapes inclined dimples[J]. CIESC Journal, 2014, (6): 2202-2210.
DOI：

SHE Baoying, PENG Xudong, MENG Xiangkai, et al. Comparison on seal performance of liquid-lubricated end face seals with different shapes inclined dimples[J]. CIESC Journal, 2014, (6): 2202-2210. DOI： 10.3969/j.issn.0438-1157.2014.06.034.

摘要

表面微孔的方向性可以改变密封间隙中流体的流向，在孔区末端汇聚产生明显的流体动压效应，使摩擦副端面打开，形成全膜润滑。以不同开孔形状（圆形、菱形、椭圆形、长方形）型孔端面密封为研究对象，考虑润滑液膜中的空化现象，基于质量守恒JFO空化算法建立数值模拟模型，采用有限差分法求解Reynolds控制方程，获得端面膜压分布。对比分析了在不同操作参数和几何结构参数下不同开孔端面密封性能。结果表明：相比于圆孔，在低速或高压下，方向性型孔都具有较好的动压效应，且长方形孔的动压开启力最好，菱形孔泄漏率较小。当膜厚h0=1.5～2.5 mm，孔深hp=2～3 mm，长短轴比γ=3～4，反向开孔比β=0.5，倾斜角α1=30°～50°、α2=120°～140°时，不同形状方向性型孔可获得最佳的动压密封性能。

Abstract

The directionality of surface dimples can guide the direction of fluid flow in the seal gap and produce fluid cumulative effect in the dimple length direction

which leads to obvious hydrodynamic effect. As a result

the seal faces separate and full film lubrication is formed. The textured mechanical face seals with different dimple shapes

such as circle

diamond

ellipse and rectangle were studied. Based on the mass-conserving JFO cavitation algorithm

a mathematical model was presented by taking the cavitation of liquid fluid between the two seal faces into consideration. The Reynolds equation was solved by use of the finite difference method

and pressure distribution was obtained. Comparative analysis of mechanical face seal performance with different dimple shapes at different operating parameters and geometric parameters was presented. The results showed that inclined dimple displayed better hydrodynamic effect than circle dimple under low speed or high pressure condition. The rectangle dimple showed the best hydrodynamic effect

and the diamond dimple had a lower leakage. Excellent hydrodynamic effect could be obtained for inclined dimple with different shapes when film thickness h0=1.5-2.5 mm

pore depth hp=2-3 mm

axial ratio γ=3-4

opponent texturing proportion β=0.5

inclination angle α1=30°-50° and α2=120°-140°.

关键词

Keywords

references

Views

256

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effect of irregular V-shaped surface texture on the performance of mechanical face seal

Analysis of surface deformation and seal performance of mechanical face seal with diamond macro-pores

Prediction of biomass pyrolysis product yield based on machine learning algorithms

Deformation and fragmentation characteristics of liquid marbles under the action of non-uniform electric field

Physics-informed spatio-temporal graph convolutional network for fermentation processes

Related Author

ZHAO Wenjing

TU Zhirong

MENG Xiangkai

JIANG Jinbo

PENG Xudong

CHENG Xiangping

MENG Xiangkai

PENG Xudong

Related Institution

College of Mechanical Engineering, Zhejiang University of Technology

School of Mechanical Engineering, Zhejiang University of Technology

MOE Engineering Center of Process Equipment and Its Manufacture, Zhejiang University of Technology

Institute of Agricultural Environment and Sustainable Development, Chinese Academy of Agricultural Sciences

Key Laboratory of Green and Low-carbon Agriculture in North China Plain, Ministry of Agriculture and Rural Affairs

⁰