Influences of inclination and cooling condition on heat transfer performance of closed loop plate pulsating heat pipe with parallel channels

SHI Weixiu; PAN Lisheng; LI Weiyi

doi:10.3969/j.issn.0438-1157.2014.02.023

您当前的位置：

首页 >

文章列表页 >

Influences of inclination and cooling condition on heat transfer performance of closed loop plate pulsating heat pipe with parallel channels

更新时间：2025-12-10

- Influences of inclination and cooling condition on heat transfer performance of closed loop plate pulsating heat pipe with parallel channels
- CIESC Journal Issue 2, Pages: 532-537(2014)
- 作者机构：
  
  1. 北京建筑大学环境与能源工程学院,北京,100044
  2. 北京建筑大学供热供燃气通风及空调工程北京市重点实验室,北京,100044
  3. 中国科学院力学研究所, 高温气体动力学国家重点实验室,北京,100190
  4. 天津大学机械工程学院,天津,300072
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2014.02.023
  CLC： K124
- Online First：05 February 2014，
  
  Published：05 February 2014
- 稿件说明：
移动端阅览
SHI Weixiu, PAN Lisheng, LI Weiyi. Influences of inclination and cooling condition on heat transfer performance of closed loop plate pulsating heat pipe with parallel channels[J]. CIESC Journal, 2014, (2): 532-537.
DOI：

SHI Weixiu, PAN Lisheng, LI Weiyi. Influences of inclination and cooling condition on heat transfer performance of closed loop plate pulsating heat pipe with parallel channels[J]. CIESC Journal, 2014, (2): 532-537. DOI： 10.3969/j.issn.0438-1157.2014.02.023.

摘要

针对多通路并联回路板式脉动热管建立实验台，采用铜质模块加热和水浴冷却方式作为热工条件，着重考察脉动热管在不同倾角（90°，75°，60°）及冷却工况（4.5 g·s-1和9.0 g·s-1）下的传热性能，通过壁面温度的振荡和传热热阻来评价其传热效果。实验结果表明，重力对多通路并联回路板式脉动热管传热性能的影响较大，随着倾角的减少，工质的回流变弱，传热热阻变大，传热极限变低；脉动热管的加热功率与冷却能力是相互匹配的，匹配度越高，脉动热管越不易干烧，传热极限越高，在有倾角的工况下提高传热极限表现得更为明显；脉动热管运行时存在一个最佳水流量，在最佳冷却工况下，脉动热管的运行热阻最低。

Abstract

An experimental setup was established based on a closed loop plate pulsating heat pipe with parallel channels and a series of experiments were conducted to study its operational performance with acetone and ethanol. Heating copper block and cold water bath were adopted as thermal conditions in the experiments. The characteristics were investigated for different inclinations (90°

75°

and 60°) and cooling conditions (4.5 and 9.0 g·s-1). The heat-transfer performance of the pulsating heat pipe was mainly evaluated by thermal resistance and wall temperature. The results show that gravity has great influence on the heat transfer. At smaller inclination

thermal resistance is larger and heat transfer limit is lower. Heating power and cooling capacity need to be matched each other

and heat transfer limit will be higher with higher matching degree

especially with inclination. There is a best mass flow rate during the operation

and the thermal resistance is the lowest under the best cooling condition.

关键词

Keywords

references

Views

254

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Novel flat plate evaporator of loop gravity assisted heat pipe for high heat flux electronic cooling

Heat transfer performance of three-dimensional oscillating heat pipe with flat-plate evaporator

Influence of SDBS on start time and heat transfer performance of pulsating heat pipe

Pool boiling heat transfer of water in porous copper foam

Heat transfer characteristics of honeycomb liquid-cooled power battery module

Related Author

XU Xiongwen

LIU Jinping

LIANG Lingjiao

QU Jian

PENG Youquan

SUN Qin

CAI Jichi

WANG Ruixiang

Related Institution

School of Electric Power, South China University of Technology

Guangdong Province Key Laboratory of Efficient and Clean Energy Utilization

State Key Laboratory of Subtropical Building Science

School of Energy and Power Engineering, Jiangsu University

Beijing Engineering Research Centre of Sustainable Energy and Buildings, Beijing University of Civil Engineering and Architecture

⁰