Numerical analysis of LaserFace liquid lubricated mechanical seal based on mass conservation

TANG Feixiang; MENG Xiangkai; LI Jiyun; PENG Xudong

doi:10.3969/j.issn.0438-1157.2013.10.029

您当前的位置：

首页 >

文章列表页 >

Numerical analysis of LaserFace liquid lubricated mechanical seal based on mass conservation

更新时间：2025-12-10

- Numerical analysis of LaserFace liquid lubricated mechanical seal based on mass conservation
- CIESC Journal Issue 10, Pages: 3694-3700(2013)
- 作者机构：
  
  浙江工业大学过程装备及其再制造教育部工程研究中心,浙江,杭州,310032
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2013.10.029
  CLC： H117.2
- Online First：05 October 2013，
  
  Published：05 October 2013
- 稿件说明：
移动端阅览
TANG Feixiang, MENG Xiangkai, LI Jiyun, et al. Numerical analysis of LaserFace liquid lubricated mechanical seal based on mass conservation[J]. CIESC Journal, 2013, (10): 3694-3700.
DOI：

TANG Feixiang, MENG Xiangkai, LI Jiyun, et al. Numerical analysis of LaserFace liquid lubricated mechanical seal based on mass conservation[J]. CIESC Journal, 2013, (10): 3694-3700. DOI： 10.3969/j.issn.0438-1157.2013.10.029.

摘要

针对传统Reynolds空化边界不能准确预测机械密封泄漏率的问题

采用JFO空化边界条件

建立了基于质量守恒的LaserFace液体润滑机械密封数学模型

采用流线迎风有限单元法求解润滑方程

对比分析了不同操作工况下4种不同端面型槽结构(普通端面、仅含引流槽端面、仅含回流槽端面、激光脸)的密封性能。结果表明:所建立数学模型可准确预测机械密封泄漏率

LaserFace端面在低速时易于打开

高速低压下回流槽具有明显回流泵送作用

LaserFace端面机械密封泄漏率显著低于仅含引流槽端面

摩擦系数小于普通端面

综合性能明显优于其他型槽结构。

Abstract

The Jakobsson-Floberg-Olsson(JFO)cavitation boundary condition was used to solve the problem that traditional Reynolds cavitation boundary condition can not accurately predict the mechanical seal leakage rate.The mathematical model of LaserFace liquid lubricated mechanical seal(LF-MS)was established based on mass conservation.Lubrication equation was solved by the streamline upwind finite element method.The comparison of sealing performance among four types of a LF-MS

a general face seal

a general face seal with "entry flow" structures

a general face seal with "return flow" structures was performed under different operating conditions.The mathematical model could accurately predict the mechanical seal leakage rate.LF-MS end face was easy to open at a low speed

Return grooves had obvious return pumping action at a high speed and low pressure.The leakage rate of LF-MS was significantly lower than a general face seal with "entry flow" structures.The friction coefficient of LF-MS was smaller than that of the general end face.The overall performance was significantly better than the others.

关键词

Keywords

references

Views

351

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Effects of waviness and taper on cavitation characteristics of liquid lubricated mechanical seals

Analysis of turbulence effect on cavitation cooling flow in mechanical seals with Rayleigh steps

Study on flow and cavitation characteristic in zigzag and array labyrinth valve core structures

Experimental and numerical simulation of ultrasonic cavitation microjet cleaning of heavy deposition in crude oil storage tank

Application progress of finite element method numerical simulation in the design of high-performance lithium secondary batteries

Related Author

HAO Muming

REN Baojie

HAN Jie

YANG Wenjing

LI Zhentao

CHEN Hao

WANG Wanlong

LI Congcong

Related Institution

Institute of Sealing Technology, China University of Petroleum

Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences

College of Petrochemical Engineering, Lanzhou University of Technology

State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University

Sichuan Huayou Group Corporation Limited， PetroChina Southwest Oil & Gasfield Company

⁰