Filling behavior of iPP micro-array structure product by micro injection molding

ZHANG Qinxing; LI Qian; DONG Zikai; JIANG Jing; WANG Lixia; SHEN Changyu

doi:10.3969/j.issn.0438-1157.2013.08.049

您当前的位置：

首页 >

文章列表页 >

Filling behavior of iPP micro-array structure product by micro injection molding

更新时间：2025-12-10

- Filling behavior of iPP micro-array structure product by micro injection molding
- CIESC Journal Issue 8, Pages: 3045-3053(2013)
- 作者机构：
  
  郑州大学橡塑模具国家工程研究中心,河南,郑州,450002
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2013.08.049
  CLC： Q320.66+2
- Online First：05 August 2013，
  
  Published：05 August 2013
- 稿件说明：
移动端阅览
ZHANG Qinxing, LI Qian, DONG Zikai, et al. Filling behavior of iPP micro-array structure product by micro injection molding[J]. CIESC Journal, 2013, (8): 3045-3053.
DOI：

ZHANG Qinxing, LI Qian, DONG Zikai, et al. Filling behavior of iPP micro-array structure product by micro injection molding[J]. CIESC Journal, 2013, (8): 3045-3053. DOI： 10.3969/j.issn.0438-1157.2013.08.049.

摘要

根据微阵列结构制品熔体的充填特性

设计直径为500 μm的微圆柱阵列结构制品模型

并加工注射成型模具

对微圆柱结构制品熔体的充填规律进行实验和模拟研究。结果表明:微结构制品熔体的充填过程和流动前沿形态的实验结果与模拟分析虽然在趋势上比较一致

但在微圆柱成型过程中

流动前沿的形成过程和充填高度的模拟变化规律与实验结果有一定偏差;实验还发现

前期充填阶段对微圆柱成型的贡献较小

微圆柱内流动前沿的形成受到熔体流动速度、微圆柱模壁、熔体流动惯性影响较大

熔体流经微圆柱结构时产生向上的流动涡流

流动前沿形状呈偏心椭球冠状并逐渐发展成球冠状。

Abstract

Filling behavior of micro-array structure product of iPP was investigated by numerical analysis and injection molding experiments.An injection mold was designed to produce products with micro-cylinder structure 500 μm in diameter.The filling process of flow front of micro-cylinders of numerical simulation and injection molding experiment was relatively consistent in the general trend.However

formation of flow front and varying patterns of the height of micro-cylinder in the filling process in the numerical simulation deviated from the experiment.Injection molding experiment showed that micro-cylinder mold wall

melt flow rate

and melt flow inertia played an important role in the formation of flow front.Early filling contributed little to the micro-cylinder molding.Turbulence appeared on the melt flow directly below the micro-cylinder.The flow front was like the shape of acentric ellipsoid crown and gradually developed into the shape of spherical crown.

关键词

Keywords

references

Views

355

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Progress of solar photo-thermo-catalysis for ammonia synthesis and decomposition under mild conditions

Methods of adaptive prediction and abnormal states traceability for sulphur content in flue gas desulfurization process

Prediction model for COD in petrochemical wastewater influent based on temporal-spatial dual-stream convolutional neural network

Oxygen mass transfer performance of hollow fiber non-bubble aeration membrane based on gas/liquid-phase measurement method

Study on the residence time distribution characteristics of the TPMS-Diamond static mixer

Related Author

No data

Related Institution

No data

⁰