Numerical simulation of droplet impact on surfaces with different wettabilities

LIANG Chao; WANG Hong; ZHU Xun; CHEN Rong; DING Yudong; LIAO Qiang

doi:10.3969/j.issn.0438-1157.2013.08.006

您当前的位置：

首页 >

文章列表页 >

Numerical simulation of droplet impact on surfaces with different wettabilities

更新时间：2025-12-10

- Numerical simulation of droplet impact on surfaces with different wettabilities
- CIESC Journal Issue 8, Pages: 2745-2751(2013)
- 作者机构：
  
  1. 重庆大学低品位能源利用及系统教育部重点实验室,重庆,400030
  2. 重庆大学工程热物理研究所,重庆,400030
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2013.08.006
  CLC： K01
- Online First：05 August 2013，
  
  Published：05 August 2013
- 稿件说明：
移动端阅览
LIANG Chao, WANG Hong, ZHU Xun, et al. Numerical simulation of droplet impact on surfaces with different wettabilities[J]. CIESC Journal, 2013, (8): 2745-2751.
DOI：

LIANG Chao, WANG Hong, ZHU Xun, et al. Numerical simulation of droplet impact on surfaces with different wettabilities[J]. CIESC Journal, 2013, (8): 2745-2751. DOI： 10.3969/j.issn.0438-1157.2013.08.006.

摘要

采用VOF方法模拟了液滴以相同速度撞击到接触角分别为63°、90°、118°和160°的固体壁面上的形态演变过程。结果表明:固壁的亲憎水性对液滴撞击表面后形态的演化有较大影响

亲水壁面有利于液滴的铺展

在接触角为90°的壁面上液滴部分反弹

而当接触角为160°时

液滴完全反弹;当三相接触线开始回缩时

中心液体的表层部分在惯性力的作用下继续向铺展的液滴边缘聚集

导致近中心处液膜逐渐减薄至断裂

最终形成边缘较厚的液环;同时

液滴最大铺展系数随壁面接触角的增大而减小

达到最大铺展系数的时间也相应缩短。

Abstract

Dynamic behavior of an impacting water droplet was simulated with the VOF(volume of fluid)method.Droplet diameter was 2.6 mm and impacting velocity was 0.5 m·s-1.Droplet dynamic behavior on simulated

hydrophilic and hydrophobic surfaces was simulated with an impacting angle of 63?

90?

118癮nd 160?.Simulation results showed reasonably good agreement with the experiment data.Surface wettability seriously affected droplet dynamic behavior.Droplet spread well and then sticked on the hydrophilic surface.On the surface with an impacting angle of 90?

droplet partly rebounded away from the surface.While droplet totally rebounded when impacting on the hydrophobic surface.There was an edge liquid ring for liquid sticking on the droplet edge when contact line draw back.The maximum spreading factor and the time needed to arrive at the maximum spread diameter were reduced with increasing contact angle.

关键词

Keywords

references

Views

611

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Incipient fault detection for dynamic chemical processes based on weighted probability CVDA

Lateral bouncing behavior of droplets on the wettability-patterned surface

Factors and critical criterion for droplet breakthrough upon impacting mesh screen membrane

Analysis of flow field characteristics and mixing performance of different SK-type static mixers

Hydrolysis reaction mechanism of CNCl on the surface of composite metal CuCr2O4

Related Author

HOU Chunwang

LIAO Mingyan

DENG Xiaogang

LIU Xiaoyue

YANG Minghui

Chunwang HOU

Xiaoyue LIU

Minghui YANG

Related Institution

College of Control Science and Engineering, China University of Petroleum

Key Laboratory of Low-Grade Energy Utilization Technologies & Systems, Ministry of Education, Chongqing University

Beijing Key Laboratory of Multiphase Flow and Heat Transfer for Low Grade Energy Utilization, North China Electric Power University

Institute of Engineering Thermophysics

Key Laboratory of Low-Grade Energy Utilization Technologies & Systems, MOE, Chongqing University

⁰