Thermodynamic analysis on optimum phase change temperature for multiple phase change materials

HU Peng; LU Dajie; ZHAO Panpan; CHEN Zeshao

doi:10.3969/j.issn.0438-1157.2013.07.003

您当前的位置：

首页 >

文章列表页 >

Thermodynamic analysis on optimum phase change temperature for multiple phase change materials

更新时间：2025-12-10

- Thermodynamic analysis on optimum phase change temperature for multiple phase change materials
- CIESC Journal Issue 7, Pages: 2322-2327(2013)
- 作者机构：
  
  中国科学技术大学热科学和能源工程系,安徽,合肥,230027
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2013.07.003
  CLC： K512
- Online First：05 July 2013，
  
  Published：05 July 2013
- 稿件说明：
移动端阅览
HU Peng, LU Dajie, ZHAO Panpan, et al. Thermodynamic analysis on optimum phase change temperature for multiple phase change materials[J]. CIESC Journal, 2013, (7): 2322-2327.
DOI：

HU Peng, LU Dajie, ZHAO Panpan, et al. Thermodynamic analysis on optimum phase change temperature for multiple phase change materials[J]. CIESC Journal, 2013, (7): 2322-2327. DOI： 10.3969/j.issn.0438-1157.2013.07.003.

摘要

采用组合式相变材料的蓄热系统较单一相变材料具有更为优越的传热和热力学性能

而相变温度对于蓄热系统性能具有重要的影响。为了使结果更具普适性

以热力学有效能分析为基础并忽略具体换热器形式和传热过程

推导了使用不同相变材料数时每种相变材料最佳相变温度的理论公式

并根据最佳相变温度计算了有效能利用率随着相变材料数的变化

结果表明当PCMs数增加到4种时

理论最大有效能利用率已达80%以上

比使用单一相变材料的理论最大有效能利用率高50%左右。以573.15 K热能蓄能为例

计算了使用1~4种相变材料时相应的最佳相变温度与最大有效能利用率

并以此为依据给出了实际最佳相变材料组合。

Abstract

A thermal storage system using multiple phase change materials (PCMs)has much better heat transfer and thermodynamic properties than that using single PCM.The phase change temperatures of multiple PCMs have an important effect on the performance of the thermal storage system.To obtain generalized results

the analysis method for thermodynamic exergy is employed

with the type of heat exchanger and heat transfer process neglected.The theoretical equation for the optimum phase change temperature of each PCM is derived.The optimum exergy efficiency is calculated for different number of PCMs.The results indicate that the exergy efficiency could be up to 80% with 4 or more PCMs

which is about 50% higher than that using single PCM.With thermal energy at 573.15 K as example

the optimum temperatures and the maximum exergy efficiencies for one to four PCMs are calculated

and the optimum combination of multiple PCMs is given on the basis of theoretical results.

关键词

Keywords

references

Views

378

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Analysis of heat transfer efficiency and rate inside fermentation tank with heating coil of biogas projects

Energy-saving optimization of partial diabatic distillation with side streams

Performance study of gas-liquid vortex separators under low cross-sectional gas velocity

Study on microwave enhanced removal performance of organic matter in coking waste salt

A two-stage dual-channel deep learning model for chemical fault classification

Related Author

ZHANG Shaopeng

HAN Ruiping

CHEN Jingjing

ZHOU Jun

LU Xiaohua

WANG Changsong

JIN Liangjie

BAI Peng

Related Institution

State Key Laboratory of Materials-Oriented Chemical Engineering, Nanjing Tech University

School of Biotechnology and Engineering, Nanjing Tech University

Bioenergy Research Institute, Nanjing Tech University

School of Chemical Engineering and Technology, Tianjin University

⁰