Numerical simulation of oscillating heat transfer characteristics in cavity partly filled with cooling liquid

CAO Yuanfu; ZHANG Weizheng; YANG Zhenyu; YUAN Yanpeng; ZHANG Ti'en

doi:10.3969/j.issn.0438-1157.2013.03.015

您当前的位置：

首页 >

文章列表页 >

Numerical simulation of oscillating heat transfer characteristics in cavity partly filled with cooling liquid

更新时间：2025-12-10

- Numerical simulation of oscillating heat transfer characteristics in cavity partly filled with cooling liquid
- CIESC Journal Issue 3, Pages: 891-896(2013)
- 作者机构：
  
  1. 北京理工大学机械与车辆学院,北京,100081
  2. 中国北方车辆研究所,北京,100072
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2013.03.015
  CLC： K124
- Online First：05 March 2013，
  
  Published：05 March 2013
- 稿件说明：
移动端阅览
CAO Yuanfu, ZHANG Weizheng, YANG Zhenyu, et al. Numerical simulation of oscillating heat transfer characteristics in cavity partly filled with cooling liquid[J]. CIESC Journal, 2013, (3): 891-896.
DOI：

CAO Yuanfu, ZHANG Weizheng, YANG Zhenyu, et al. Numerical simulation of oscillating heat transfer characteristics in cavity partly filled with cooling liquid[J]. CIESC Journal, 2013, (3): 891-896. DOI： 10.3969/j.issn.0438-1157.2013.03.015.

摘要

振荡强化传热在内燃机活塞和气门中得到广泛应用

但是其热量输运机理了解还不够深入

目前仍然主要基于经验进行活塞和气门冷却结构的设计

这无疑使得系统传热量难以准确确定。采用CFD动网格技术和VOF多相流模型

对封闭空腔中填充部分冷却介质的振荡传热进行了数值计算

分析了对流传热系数随转速、冲程以及填充率的变化规律。结果表明:振荡能够明显地强化传热

转速是影响振荡强化传热的主要因素

强化传热的效果随着转速以及活塞冲程的增大而增强;当冷却介质填充率在30%～60%范围内时

强化传热效果明显

但当冷却介质填充率超出此范围时

传热效果变差。分析结果对内燃机活塞及气门的冷却设计具有指导意义。

Abstract

Oscillating heat transfer has been widely used in engine pistons and valves

but the mechanism of heat transport is still not clearly understood

so the design of liquid cooled pistons and valves is mostly based on empirical knowledge and it is difficult to achieve appropriate heat transfer rate.In this study

a numerical simulation on oscillating heat transfer characteristics in a cavity partly filled with cooling liquid was performed by using CFD dynamic mesh method and volume of fluid(VOF) model.The relations of heat transfer coefficient to the speed and stroke of piston and fill ratio of liquid were obtained.The results indicate that the oscillation enhances the heat transfer significantly.The rotation speed is the major factor affecting heat transfer

and the heat transfer enhancement is reinforced with the increase of rotation speed and piston of stroke.When the fill ratio range of liquid is 30%—60%

the enhancement of heat transfer is remarkable

otherwise the effect of enhancement is unsatisfactory.The results are helpful to the design of pistons and valves.

关键词

Keywords

references

Views

427

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Heat transfer and flow characteristics of nanofluids in microchannels

Analysis of flow and heat transfer characteristics of lubricating oil in circular tube with coaxial crossed vortex generators

Study on heat and mass transfer and nonlinear characteristics with heat and mass source in cavity

Characteristics of enhanced heat transfer of twisted elements with varying twist ratio

Heat transfer enhancement of heat tube with variable cross-section

Related Author

LIU Ping

QIU Yusheng

LI Shijing

SUN Ruiqi

SHEN Chen

LIN Zhimin

WANG Chongzhao

QIANG Guozhi

Related Institution

School of Mechatronics Engineering, Anhui University of Science and Technology

School of Mechanical Engineering, Lanzhou Jiaotong University

Key Laboratory of Railway Vehicle Thermal Engineering, Ministry of Education

School of Energy and Power Engineering, University of Shanghai for Science and Technology

Pudong New Area Special Equipment Supervision and Inspection Institution

⁰