Dynamic opening characteristics of dry gas seals with typical types of spiral grooves

PENG Xudong; LIU Kun; BAI Shaoxian; LI Jiyun; SHENG Song

doi:10.3969/j.issn.0438-1157.2013.01.037

您当前的位置：

首页 >

文章列表页 >

Dynamic opening characteristics of dry gas seals with typical types of spiral grooves

更新时间：2025-12-10

- Dynamic opening characteristics of dry gas seals with typical types of spiral grooves
- CIESC Journal Issue 1, Pages: 326-333(2013)
- 作者机构：
  
  浙江工业大学过程装备及其再制造教育部工程研究中心,浙江,杭州,310032
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2013.01.037
  CLC： H117.2
- Online First：05 January 2013，
  
  Published：05 January 2013
- 稿件说明：
移动端阅览
PENG Xudong, LIU Kun, BAI Shaoxian, et al. Dynamic opening characteristics of dry gas seals with typical types of spiral grooves[J]. CIESC Journal, 2013, (1): 326-333.
DOI：

PENG Xudong, LIU Kun, BAI Shaoxian, et al. Dynamic opening characteristics of dry gas seals with typical types of spiral grooves[J]. CIESC Journal, 2013, (1): 326-333. DOI： 10.3969/j.issn.0438-1157.2013.01.037.

摘要

型槽端面干式气体密封的开启特性对密封的启动、停车和运行具有重要实际意义。基于气体混合润滑理论

考虑密封端面粗糙度效应和端面间气体滑移流效应

建立了干式气体密封的动压开启性能分析模型。开展了螺旋槽端面干式气体密封、带内环槽的螺旋槽端面干式气体密封和雁型槽端面干式气体密封等三种典型型槽端面干式气体密封的临界动压开启性能研究

数值分析了不同工况下三种型槽密封端面气膜压力分布

研究了环颈长比、环颈宽比、平衡比、弹簧比压和密封压力对临界开启转速、动压开启力比等开启性能参数的影响规律。结果表明:端面型槽的动压效应直接决定干式气体密封的临界开启转速

平衡比、弹簧比压对密封的动压开启性能影响较大

而环颈长比影响很小;在相同操作条件下

三种型槽端面密封相比较

雁型槽端面干式气体密封最易开启

带内环槽的螺旋槽端面干式气体密封次之

螺旋槽端面干式气体密封最难开启。

Abstract

The opening behavior of two sealing faces of a dry gas seal (DGS) with various types of specified grooves is very important for startup

shut down

and operation of the DGS.Based on the theory of gas mixed lubrication

a dynamic opening model for a DGS was developed by considering the effects of gaseous slip flow and surface roughness.In the present paper

the critical dynamic sealing behavior

especially the opening characteristics of three types of DGSs were studied

including the spiral-groove DGS (S-DGS)

the spiral groove and annular groove DGS (AS-DGS)

and the goose groove DGS (GS-DGS).The gas film pressure distributions between two sealing faces of three types of DGSs under different operating conditions were numerically analyzed.A series of simulations were carried out to study the influences of annular neck length ratio

annular neck width ratio

balance ratio

spring pressure and sealed medium pressure on the critical opening rotational speed and hydrodynamic opening force ratio.Results showed that the critical opening rotational speed was directly determined by dynamic pressure effect of the specified face grooves.Dynamic opening characteristics were greatly affected by balance ratio and spring pressure

and slightly affected by annular neck length ratio.A comparison of the dynamic opening characteristics among the three types of DGSs was made under the same operating conditions.The results showed that the GS-DGS opened most quickly

the AS-DGS secondly

and the S-DGS most slowly during the startup process.

关键词

Keywords

references

Views

419

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Performance analysis and structural optimization of double-sided spiral groove-type dry gas seal

Influence of micro-texture size and areal density on surface of silicon carbide on tribological properties of sliding sealing surfaces

Study on influence of operating conditions on thermodynamic process and steady state performance of supercritical CO2 dry gas seal

Study on critical chocked characteristics of supercritical carbon dioxide spiral groove dry gas seal under thermal-fluid coupling lubrication

Flow simulation and sealing performance test of ultra-high speed dry gas seal under multiple effects

Related Author

WANG Yan

WANG Yutong

CHEN Miaomiao

HE Yiming

LIU Wei

DING Dejun

MA Chenbo

ZHANG Chening

Related Institution

Sinoseal Holding Co., Ltd.

School of Mechanical and Electronic Engineering, Nanjing Forestry University

Ningbo Fangli Seals Co., Ltd.

School of Mechanical Engineering, Jiangsu Ocean University

College of Mechanical Engineering, Zhejiang University of Technology

⁰