Contact characterizations of end faces in mechanical seals running-in

WEI Long; GU Boqin; ZHANG Penggao; FANG Guifang

doi:10.3969/j.issn.0438-1157.2012.10.028

您当前的位置：

首页 >

文章列表页 >

Contact characterizations of end faces in mechanical seals running-in

更新时间：2025-12-10

- Contact characterizations of end faces in mechanical seals running-in
- CIESC Journal Issue 10, Pages: 3202-3207(2012)
- 作者机构：
  
  1. 南京化工职业技术学院流体密封与测控技术研究所,江苏,南京,210048
  2. 江苏省流体密封与测控工程技术研究开发中心,江苏,南京,210048
  3. 南京工业大学机械与动力工程学院,江苏,南京,211816
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2012.10.028
  CLC： H136TH117.1
- Online First：05 October 2012，
  
  Published：05 October 2012
- 稿件说明：
移动端阅览
WEI Long, GU Boqin, ZHANG Penggao, et al. Contact characterizations of end faces in mechanical seals running-in[J]. CIESC Journal, 2012, (10): 3202-3207.
DOI：

WEI Long, GU Boqin, ZHANG Penggao, et al. Contact characterizations of end faces in mechanical seals running-in[J]. CIESC Journal, 2012, (10): 3202-3207. DOI： 10.3969/j.issn.0438-1157.2012.10.028.

摘要

为研究和掌握机械密封磨合过程端面接触特性的变化规律

考虑机械密封端面微凸体实际微接触面积与微接触截面积之间的区别

对微凸体临界弹性变形微接触面积和临界塑性变形微接触面积的表达式进行修正;推导得出机械密封端面弹性接触面积比、弹塑性接触面积比和塑性接触面积比的表达式。对B104a-70型机械密封进行磨合试验

试验介质为20℃清水

压力为0.5 MPa

弹簧比压为0.15 MPa

转速为2900 r·min-1。研究结果表明

随着磨合过程的进行

软质环端面迅速趋于光滑

磨损率迅速减小;磨合使密封端面间的接触特性发生了较大的变化

量纲1真实接触面积由0.00348增大到0.00567

弹性接触面积比由0.716增大到0.822

弹塑性接触面积比由0.231降低到0.128

塑性接触面积比由0.053降低到0.050。

Abstract

In order to study the change of contact characterizations of end faces in mechanical seal running-in

taking into account the difference between real micro contact area and micro contact cross-sectional area of end faces of mechanical seals

the expressions of the micro-contacting areas related to the critical elastic and plastic deformations were revised.The expressions of elastic contact area ratio

elastic-plastic contact area ratio and plastic contact area ratio for mechanical seals were derived.Running-in tests of B104a-70 mechanical seals were made with water as test medium.Test temperature was 20℃. Test pressure was 0.5 MPa. Spring pressure was 0.15 MPa. Rotating speed was 2900 r·min-1.The results showed that the end face of the soft ring tended to be smoothened rapidly and its wear rate decreased quickly in running-in.The contact characterizations between end faces of mechanical seals changed greatly.The normalized real contact area increased from 0.00348 to 0.00567. The elastic contact area ratio increased from 0.716 to 0.822.The elastic-plastic contact area ratio decreased from 0.231 to 0.128. The plastic contact area ratio decreased from 0.053 to 0.050.

关键词

Keywords

references

Views

250

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Average film thickness prediction of end faces in contacting mechanical seals in running-in period

Fractal model of temperature distribution of frictional interface in contacting mechanical seals

Research on friction and wear characteristics of mechanical seals in start-stop phases based on 3D fractal end-face characterization

Analysis of turbulence effect on face groove cooling performance of high-speed mechanical seals

Research on thermal mechanical coupling deformation and friction and wear of mechanical seal for granular medium

Related Author

WEI Long

ZHANG Penggao

FANG Guifang

DING Xuexing

YAN Ruqi

CHEN Jinlin

ZHAI Xiao

CHEN Kaifang

Related Institution

Fluid Sealing Measure and Control Engineering Research and Development Center of Jiangsu Province, Nanjing College of Chemical Technology

School of Petrochemical Engineering, Lanzhou University of Technology

Research Center of Fluid Sealing Technology, Beijing University of Chemical Technology

College of Mechanical and Electrical Engineering, Beijing University of Chemical Technology

College of Petrochemical Engineering, Lanzhou University of Technology

⁰