Temperature measuring point analysis and control system design of heat exchanger networks based on structural observability

LUO Xionglin1; HOU Benquan1; SUN Lin1; 2

doi:10.3969/j.issn.0438-1157.2012.01.021

您当前的位置：

首页 >

文章列表页 >

Temperature measuring point analysis and control system design of heat exchanger networks based on structural observability

更新时间：2025-12-10

- Temperature measuring point analysis and control system design of heat exchanger networks based on structural observability
- CIESC Journal Issue 1, Pages: 146-156(2012)
- 作者机构：
  
  1. 1中国石油大学自动化研究所
  2. 不列颠哥伦比亚大学化学与生物工程学院
- 作者简介：
- 基金信息：
- DOI：10.3969/j.issn.0438-1157.2012.01.021
  CLC：
- Online First：05 January 2012，
  
  Published：05 January 2012
- 稿件说明：
移动端阅览
LUO Xionglin1, HOU Benquan1, SUN Lin1, et al. Temperature measuring point analysis and control system design of heat exchanger networks based on structural observability[J]. CIESC Journal, 2012, (1): 146-156.
DOI：

LUO Xionglin1, HOU Benquan1, SUN Lin1, et al. Temperature measuring point analysis and control system design of heat exchanger networks based on structural observability[J]. CIESC Journal, 2012, (1): 146-156. DOI： 10.3969/j.issn.0438-1157.2012.01.021.

摘要

复杂换热网络中间温度状态变量众多且变量间耦合严重，若不加以控制与观测，往往不利于物流间的热量传递与安全监测。换热网络的温度测点设置是实施控制的基础，为保证全部状态的可观性，凭经验设置的温度测点往往过多，经济性差，也缺乏理论论证与分析。因此从控制理论的角度，基于结构可观性理论分析换热网络的结构特性。分析旁路设置对换热网络结构可观性的影响，权衡可观性与经济性两方面因素，为实现设置最少的温度测点以满足全部状态的可观性要求，提出了换热网络全部状态可观的温度测点优化设计法。然后，基于相对增益分析，将已有旁路与优化得出的温度测点进行配对，构成换热网络的常规控制系统。最后，以某常减压蒸馏装置脱盐前换热网络为例验证了方法的可行性。

Abstract

For the large scale heat exchanger networks(HEN)

there are a mass of coupled temperatures. If these states cannot be controlled and observed

it will go against saving energy and safety in production.To implement control system

placing the temperature measuring points in the HEN properly is the basis.Generally

too many thermocouples are set by experience to ensure all states of the HEN are observable.But it is not cost-efficient and lack of verification by the control theory.Therefore

it is necessary to develop a method to design temperature measuring points of HEN based on the control theory. An optimal design method of temperature measuring points with all states observable was proposed by using structural observability and analysis of the impact of bypasses.The design could maintain all of states observable and minimize the number of temperature measuring points with the trade-off between observability and capital investment.With measuring points determined

the regulatory control system was proposed based on the relative gain array analysis.Consequently

a case study with HEN in a crude distillation unit demonstrated the effectiveness of the method proposed.

关键词

Keywords

references

Views

407

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Performance analysis and structural optimization of double-sided spiral groove-type dry gas seal

ANN-GA integrated framework for intelligent screening of ORC mixture working fluids and performance optimization

3D printing combined with freeze-drying to construct hierarchical SiO2-doped HA bioceramic scaffolds

Characteristics research of the charge-hold-vent method for cryogenic propellant tank chilldown in microgravity

Hydrolysis reaction mechanism of CNCl on the surface of composite metal CuCr2O4

Related Author

WU Xiaolong

HUANG Xiaohuang

XIAO Yuan

SHAN Linghai

YE Jiahui

CUI Guomin

WANG Yan

WANG Yutong

Related Institution

School of Energy and Power Engineering, University of Shanghai for Science and Technology

School of Mechanical Engineering, Jiangsu Ocean University

Ningbo Fangli Seals Co., Ltd.

School of Mechanical and Electronic Engineering, Nanjing Forestry University

Sinoseal Holding Co., Ltd.

⁰