Composite model of heat transfer and phase transition with high gas and liquid density ratio

LIU Bingbing; WANG Mingyu; GAO Hongtao; ZHANG Shaojun

doi:10.11949/j.issn.0438-1157.20180021

您当前的位置：

首页 >

文章列表页 >

Composite model of heat transfer and phase transition with high gas and liquid density ratio

更新时间：2025-12-10

- Composite model of heat transfer and phase transition with high gas and liquid density ratio
- CIESC Journal Issue 8, Pages: 3418-3427(2018)
- 作者机构：
  
  1. 山东交通学院船舶与轮机工程学院,山东,威海,264310
  2. 大连海事大学轮机工程学院,辽宁,大连,116026
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20180021
  CLC： 359
- Online First：05 August 2018，
  
  Published：05 August 2018
- 稿件说明：
移动端阅览
LIU Bingbing, WANG Mingyu, GAO Hongtao, et al. Composite model of heat transfer and phase transition with high gas and liquid density ratio[J]. CIESC Journal, 2018, (8): 3418-3427.
DOI：

LIU Bingbing, WANG Mingyu, GAO Hongtao, et al. Composite model of heat transfer and phase transition with high gas and liquid density ratio[J]. CIESC Journal, 2018, (8): 3418-3427. DOI： 10.11949/j.issn.0438-1157.20180021.

摘要

为研究两相流动中热量传递机制，基于格子Boltzmann热模型及大密度比模型，将相变源项引入到控制两相密度分布函数中，来描述温度场对气液相变的影响，提出了一个可以描述气液密度比达到2778的传热相变复合模型。通过对压力速度分布函数的回归修正克服了气液密度比过大造成的数值不稳定问题。模拟了溴化锂水溶液中双气泡的上升运动过程及周围的温度场分布，研究发现：双气泡上升时，碰撞前上方气泡温度高于下方气泡，碰撞时，两气泡间液桥打开，发生热量传递，气泡内部温度变得均匀；双气泡体积先减小再增大，碰撞时体积达到最大值，在融合成一个气泡后体积逐渐缩小，最终趋于稳定；初始气泡的体积越大，气泡上升过程中的速度越大。

Abstract

Based on lattice Boltzmann thermal model and large density ratio model

a phase transition source term was introduced into two-phase density distribution control function to describe effect of temperature field on gas-liquid phase transition. A composite lattice Boltzmann thermal model

which can describe heat transfer and phase transition at gas-liquid ratio up to 2778

was proposed to study two-phase heat transfer mechanism. Numerical instability caused by extremely large gas-liquid density ratio was resolved by regress correction of pressure velocity distribution function. Double bubble rising movement and the surrounding temperature field distribution in lithium bromide solution was simulated using the model. Upper bubble temperature was higher than that of lower bubble prior to collision during moving up. Upon coalescence

liquid bridge between the two bubbles was open

heat transfer started and temperature inside the bubble became uniform. The volume of the double bubbles decreased first and then increased with maximum at time of two bubbles collision. After bubble coalescence

the volume gradually decreased and eventually stabilized to certain value. The larger the initial bubble volume is

the greater the velocity of the bubble rises.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Numerical study on flow and heat transfer characteristics of airfoil printed circuit heat exchangers

Study on flow and heat transfer mechanism of supercritical CO2 in inclined upward tube under cooling conditions

Optimization on parameter of plate-fin-and-tube air cooler in mines based on response surface method

Performance analysis of printed circuit heat exchanger for supercritical carbon dioxide

Study on influence of mechanical stirring on heat transfer characteristics during jet heating of crude oil storage tank

Related Author

REN Guanyu

ZHANG Yifei

LI Xinze

DU Wenjing

DONG Xinyu

BIAN Longfei

YANG Yiyi

ZHANG Yuxuan

Related Institution

School of Energy and Power Engineering, Shandong University

Hebei Key Laboratory of Low Carbon and High Efficiency Power Generation Technology, North China Electric Power University

State Key Laboratory of Intelligent Construction and Healthy Operation and Maintenance of Deep Underground Engineering, China University of Mining and Technology

School of Mechanics and Civil Engineering, China University of Mining and Technology

China Coal Construction Company

⁰