Analysis of influencing factors of sealing face performance of mechanical seal coating

LI Shuangxi; SUN Xiandong; ZHANG Peng

doi:10.11949/j.issn.0438-1157.20171544

您当前的位置：

首页 >

文章列表页 >

Analysis of influencing factors of sealing face performance of mechanical seal coating

更新时间：2025-12-10

- Analysis of influencing factors of sealing face performance of mechanical seal coating
- CIESC Journal Issue 7, Pages: 3181-3189(2018)
- 作者机构：
  
  北京化工大学机电工程学院,北京,100029
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20171544
  CLC： B301
- Online First：05 July 2018，
  
  Published：05 July 2018
- 稿件说明：
移动端阅览
LI Shuangxi, SUN Xiandong, ZHANG Peng. Analysis of influencing factors of sealing face performance of mechanical seal coating[J]. CIESC Journal, 2018, (7): 3181-3189.
DOI：

LI Shuangxi, SUN Xiandong, ZHANG Peng. Analysis of influencing factors of sealing face performance of mechanical seal coating[J]. CIESC Journal, 2018, (7): 3181-3189. DOI： 10.11949/j.issn.0438-1157.20171544.

摘要

机械密封覆层密封环能够综合利用耐磨覆层与韧性基体材料的优良特性，但其应用主要依靠经验，缺乏针对其性能的研究。利用ANSYS软件建立釜用机械密封动环、静环和静环座组成的热-结构耦合模型，综合考虑覆层端面变形、液膜反压和密封环温度之间的相互作用，并试验验证了分析模型的正确性。分析覆层结构和材料组合对密封端面最大端面比压与速度的乘积（PbV）max、最高端面温度Tmax，覆层表面最大拉应力σmax、主界面最大切应力τmax、侧界面最大切应力σcmax和最大法向拉应力τcmax的影响，并确定最佳的覆层结构和材料组合。分析结果表明：覆层厚度、覆层与基体的热膨胀系数比和弹性模量比的变化主要影响覆层表面最大拉应力；覆层端面设计中，覆层厚度取值宜在0.4～0.6 mm，喷涂角度宜取15°～30°，覆层与基体的热膨胀系数比宜在0.5以上，弹性模量比宜在2.5以下。

Abstract

The application of sealing ring for mechanical coating

which combines the characteristics of wearresistant coating with the characteristics of the toughness base material

depends on experience. There is a lack of research on its performance. A thermal structural coupling model consisting of rotating seal ring

stationary seal ring and stationary ring seat was established by using ANSYS software. It considers the influence of the coating surface deformation

the liquid film reverse pressure and the temperature between the sealing rings. The correctness of the analytical model is validated by the experiment. The influence of coating structure and material on the product of seal face pressure and maximum velocity ((PbV)max)

the seal face in the highest end temperature (Tmax)

coatings on the surface of the maximum tensile stress (σmax)

maximum shear stress of the main interface (τmax)

the interface maximum side effect of shear stress (σcmax) and the maximum tensile stress (τcmax) was analyzed

and the coating structure and material were determined. The results show that the coating thickness

the coating and the substrate of the thermal expansion coefficient and elastic modulus ratio mainly affect the coating surface of the maximum tensile stress. For the coating surface design the thermal expansion coefficient of coating and substrate should be more than 0.5

the spraying angle should be 15°-30°

the elastic modulus ratio should be below 2.5

and the coating thickness should be 0.4-0.6 mm.

关键词

Keywords

references

Views

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Research on friction and wear characteristics of mechanical seals in start-stop phases based on 3D fractal end-face characterization

Analysis of turbulence effect on face groove cooling performance of high-speed mechanical seals

Research on thermal mechanical coupling deformation and friction and wear of mechanical seal for granular medium

Evaluation on liquid film cavitation capacity in reverse Rayleigh step and cavitation suction effect in its mechanical seals

Performance analysis on diffuser self-pumping hydrodynamic and hydrostatic mechanical seal

Related Author

CHEN Kaifang

LI Shuangxi

BI Enzhe

SUN Yuhui

TIAN Jupeng

WANG Lei

ZHANG Weizheng

ZHAO Jijun

Related Institution

Research Center of Fluid Sealing Technology, Beijing University of Chemical Technology

College of Petrochemical Engineering, Lanzhou University of Technology

College of Mechanical Engineering, Zhejiang University of Technology

College of Mechanical and Electrical Engineering, Nanjing Forestry University

School of Chemical Engineering, Sichuan University

⁰