Optimization membrane module structure of column type by CFD

XIONG Changchuan; LI Weixing; LIU Yefei; XING Weihong

doi:10.11949/j.issn.0438-1157.20170243

您当前的位置：

首页 >

文章列表页 >

Optimization membrane module structure of column type by CFD

更新时间：2025-12-10

- Optimization membrane module structure of column type by CFD
- CIESC Journal Issue 11, Pages: 4341-4350(2017)
- 作者机构：
  
  南京工业大学化工学院, 材料化学工程国家重点实验室,江苏,南京,210009
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20170243
  CLC： Q028.8
- Online First：05 November 2017，
  
  Published：05 November 2017
- 稿件说明：
移动端阅览
XIONG Changchuan, LI Weixing, LIU Yefei, et al. Optimization membrane module structure of column type by CFD[J]. CIESC Journal, 2017, (11): 4341-4350.
DOI：

XIONG Changchuan, LI Weixing, LIU Yefei, et al. Optimization membrane module structure of column type by CFD[J]. CIESC Journal, 2017, (11): 4341-4350. DOI： 10.11949/j.issn.0438-1157.20170243.

摘要

采用Euler模型与多孔介质模型对不同结构的柱式膜组件内的流体流动进行了计算模拟。研究了曝气孔数目（开孔率为1.92%保持不变）与膜组件高度对膜组件膜丝填充区域内的气液两相分布、壁面剪应力、湍流黏度以及液相速度场的影响。计算模拟数据与实验结果吻合良好。计算模拟表明：通过减小曝气孔直径，增加曝气孔数目的方式能够促进气液两相流场与液相速度场的均匀分布，以及壁面剪应力与湍流黏度的增强；增加膜组件的高度，有利于增加单支膜组件膜面积的同时充分利用曝气擦洗过程中气液两相流对膜丝壁面进行高效的气擦洗。综合考虑膜组件的安装运输、膜丝通量分布以及能耗等因素，对于直径250 mm的膜组件采用曝气孔的直径为6.32 mm，数目为30个，长度在2~2.5 m之间为最优。

Abstract

Gas-liquid two-phase fluid in membrane module of different column type was simulated by Euler model and porous medium model. The effect of the length of membrane module and the number of aerator holes (opening rate=1.92%) on gas-liquid distribution

wall shear stress

turbulent viscosity and velocity of liquid was investigated by CFD simulation. The simulation results showed good agreement with the experimental data. The results demonstrated that uniform distribution of gas-liquid and water velocity

the intensity of wall shear stress and turbulent viscosity was efficiently improved by decreasing the diameter of aerator holes and increasing the number of aerator holes; increasing the length of membrane module was significantly benefit to improve the capacity of a single membrane module

and make full use of gas scrub the wall of membrane. Considering installation

transportation

distribution of membrane flux and energy consumption

the membrane module with the diameter 250 mm that the diameter and the number of aerator holes respectively is 6.32 mm and 30

and the length of membrane module is 2-2.5 m exhibited a best performance.

关键词

Keywords

references

Views

217

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Two-phase flow and reaction in radial moving beds for propane dehydrogenation

Investigation on the static properties and annihilation characteristics of particle clusters in gas-solid fluidized beds

CaSO₄ fouling characteristics in spiral-wound RO membrane feed channel

Simulation of liquid-liquid two-phase flow in a pilot-plant scale annular pulsed disc and doughnut extraction column

Research on the flow and heat transfer characteristics of single-phase immersion coolants and liquid cooling system

Related Author

LI Jian

SUN Zhaolun

LIU Qi

LIU Mengxi

JIANG Guiyuan

LU Chunxi

XU Chunming

WANG Zhifeng

Related Institution

State Key Laboratory of Heavy Oil Processing, China University of Petroleum

Lanzhou Petrochemical Research Center, Petrochemical Research Institute, PetroChina

State Key Laboratory of Mesoscience and Engineering, Institute of Process Engineering, Chinese Academy of Sciences

School of Chemical Engineering, University of Chinese Academy of Sciences

College of Electrical Engineering, Xinjiang University

⁰