Selection and process optimization of ionic liquids for desulfurization

FANG Jing; ZHANG Shuting; LI Tingting; LI Chunli

doi:10.11949/j.issn.0438-1157.20170182

您当前的位置：

首页 >

文章列表页 >

Selection and process optimization of ionic liquids for desulfurization

更新时间：2025-12-10

- Selection and process optimization of ionic liquids for desulfurization
- CIESC Journal Issue 9, Pages: 3434-3441(2017)
- 作者机构：
  
  河北工业大学化工学院,天津,300130
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20170182
  CLC： Q028.3
- Online First：05 September 2017，
  
  Published：05 September 2017
- 稿件说明：
移动端阅览
FANG Jing, ZHANG Shuting, LI Tingting, et al. Selection and process optimization of ionic liquids for desulfurization[J]. CIESC Journal, 2017, (9): 3434-3441.
DOI：

FANG Jing, ZHANG Shuting, LI Tingting, et al. Selection and process optimization of ionic liquids for desulfurization[J]. CIESC Journal, 2017, (9): 3434-3441. DOI： 10.11949/j.issn.0438-1157.20170182.

摘要

针对基于COSMO-SAC模型分子设计方法的准确性问题，采用离子液体脱硫机理分析和实验的方法对其进行了验证，即对[HMIM] [BF4]、[HMIM] [PF6]、[BMIM] [BF4]、[BMIM] [PF6]、[EMIM] [BF4]、[EMIM] [PF6] 6种离子液体作萃取剂时的脱硫效果进行了脱硫机理的分析和实验的验证，得到的脱硫性能排序与离子液体分子设计结果基本一致，且均认为[HMIM] [PF6]脱硫率较高。以[HMIM] [PF6]为萃取剂，通过液相色谱法测定萃取后的液相组成，考察萃取时间、萃取温度、剂油比3个因素对脱硫率、分配系数和选择性系数的影响。通过正交实验设计确定了萃取时间40 min、萃取温度20℃、剂油比2：1为较优操作条件，单次脱硫率为72.74%，四级萃取可将模型油的含硫量由1200 μg·g-1降至6.98 μg·g-1，符合国Ⅴ标准。

Abstract

To verify the reliability of ionic liquids' molecular design method based on COSMO-SAC model

ionic liquids desulfurization mechanism analysis and experimental results are compared with COSMO simulation. By analyzing[HMIM] [BF4]

[HMIM] [PF6]

[BMIM] [BF4]

[BMIM] [PF6]

[EMIM] [BF4] and[EMIM] [PF6] on mechanism level

[HMIM] [PF6] was considered as a better extractive desulfurization agent than others

and the order of desulfurization efficiency was consistent with the calculation results from COSMO-SAC model. The experimental result shows that the difference between the COSMO simulation and experiments is not significant. In this study

[HMIM] [PF6] was used as an extractive desulfurization agent to remove benzothiophene from fuels

and the change of sulfur content in model oil was determined by liquid chromatography. Through considering the effect of extraction temperature

time and the ratio of solvent to oil

the optimal operating conditions

20℃

40 min and 2:1 respectively

were determined in orthogonal experiment with an efficiency over 72.74%. With[HMIM] [PF6] used as the deep extraction desulfurization solvent

the sulfur content decreased from 1200 μg·g-1 to 6.98 μg·g-1 by 4-stages extraction

which met the Phase Ⅴ Emission Standards in China.

关键词

Keywords

references

Views

239

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Application of aluminum-copper bimetallic ionic liquids in 1-hexene/n-hexane separation

Absorption characteristics and mechanism of VOCs by tributyl(propyl)phosphonium ionic liquid

Multi-scale simulation and study of volatile phenols removal from simulated oil by ionic liquids

Study on selective extraction of nicotine by ionic liquids composite extractant and DFT calculation

Solvents selection for separation of biphenyl from FCC diesel: experimental and computational thermodynamics

Related Author

CUI Jiaxin

YIN Mengfan

ZHENG Tao

LIU Han

ZHANG Rui

LIU Zhichang

LIU Haiyan

XU Chunming

Related Institution

State Key Laboratory of Heavy Oil Processing, China University of Petroleum

School of Chemical Engineering, China University of Mining and Technology

State Key Laboratory of Chemical Resource Engineering, Beijing University of Chemical Technology

School of Energy Science and Engineering, Central South University

Key Laboratory of Chemical Engineering Green Process of Xinjiang Production and Construction Corps, Shihezi University

⁰