Characteristics of flow condensation heat transfer for R134a in pump-assisted heat pipe

SHAO Jie; MA Tengfei; ZHANG Didi; CAO Xiaoyu; TIAN Xiaoliang

doi:10.11949/j.issn.0438-1157.20170111

您当前的位置：

首页 >

文章列表页 >

Characteristics of flow condensation heat transfer for R134a in pump-assisted heat pipe

更新时间：2025-12-10

- Characteristics of flow condensation heat transfer for R134a in pump-assisted heat pipe
- CIESC Journal Issue 7, Pages: 2713-2721(2017)
- 作者机构：
  
  青岛大学能源工程研究所,山东,青岛,266071
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20170111
  CLC： K124
- Online First：05 July 2017，
  
  Published：05 July 2017
- 稿件说明：
移动端阅览
SHAO Jie, MA Tengfei, ZHANG Didi, et al. Characteristics of flow condensation heat transfer for R134a in pump-assisted heat pipe[J]. CIESC Journal, 2017, (7): 2713-2721.
DOI：

SHAO Jie, MA Tengfei, ZHANG Didi, et al. Characteristics of flow condensation heat transfer for R134a in pump-assisted heat pipe[J]. CIESC Journal, 2017, (7): 2713-2721. DOI： 10.11949/j.issn.0438-1157.20170111.

摘要

针对动力型热管内流动凝结传热过程中的特性复杂未知，搭建了动力型热管冷凝特性测试实验台。对不同流量及干度下的R134a管内流动凝结过程中的压降特性和传热特性进行了实验研究，实验结果表明：压降随着管内工质质量流量和气体干度的增加而增加，与文献中3种不同压降模型进行了比较，得出Muller-Steinhagen-Heck模型能更好地预测管内流动凝结过程中的压降特性。传热系数随着管内工质质量流量和气体干度的增加而增加，并且低干度区的增长斜率要明显大于高干度区的增长斜率，与文献中4种不同传热模型进行了比较，得出Chen模型能更好地预测管内流动凝结过程中的传热特性。该研究为泵的选择、换热器的设计、系统的优化以及两相流凝结相变过程的研究提供了理论参考。

Abstract

The experimental facility about the test of pressure drop and heat transfer coefficient in pump-assisted heat pipe was built for the study of characteristics during flow condensation heat transfer. The experimental investigation about characteristics during flow condensation heat transfer of R134a in pump-assisted heat pipe at different mass flux and vapor quality was conducted. The experimental results indicated that pressure drop increases with the increasing vapor quality and the mass flux. The experimental results were compared with three different pressure drop models and the conclusion that Muller-Steinhagen-Heck model can better predict the characteristics of pressure drop in the process of flowing condensation is obtained. In addition

the experimental results indicated that heat transfer coefficient increases with the increasing vapor quality and the mass flux and the growth slope of low vapor quality is higher than that of high vapor quality. The experimental results were compared with four different heat transfer models and the conclusion that Chen model can better predict the characteristics of heat transfer in the process of flowing condensation is obtained. The study provides a theoretical reference for the selection of the pump

the design of the heat exchanger

the optimization of the system and the study of two-phase flow condensation.

关键词

Keywords

references

Views

213

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Film condensation heat transfer characteristics of R1234ze(E) on a horizontal three-dimensional finned tube

Numerical simulation of condensation in horizontal circular and square minichannels using R134a

Analysis of influence factors for heat transfer and pressure drop characteristics of moist air in metal foams during dehumidifying process

Shell-side heat transfer and pressure drop of shell-and-tube heat exchanger with trefoil-hole baffles

Characteristics of flow pattern for condensation heat transfer of R32 in horizontal small tube

Related Author

TIAN Haochen

MA Zhixian

WANG Zhihao

ZHANG Jingzhi

LI Wei

WENG Xiaomin

HU Haitao

ZHUANG Dawei

Related Institution

Institute of Building Energy, Dalian University of Technology

College of Energy Engineering, Zhejiang University

Collaborative Innovation Center of Advanced Aero-Engine

Research Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University

Key Laboratory of Pressure Systems and Safety, Ministry of Education, East China University of Science and Technology

⁰