Viscous dissipation effect of polymer melt in a rectangular cross section micro mold channel

YU Tongmin; ZHANG Zhengkai; ZOU Dejian

doi:10.11949/j.issn.0438-1157.20161529

您当前的位置：

首页 >

文章列表页 >

Viscous dissipation effect of polymer melt in a rectangular cross section micro mold channel

更新时间：2025-12-10

- Viscous dissipation effect of polymer melt in a rectangular cross section micro mold channel
- CIESC Journal Issue 4, Pages: 1306-1317(2017)
- 作者机构：
  
  大连理工大学机械工程学院,辽宁,大连,116024
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20161529
  CLC： Q311TG76
- Online First：05 April 2017，
  
  Published：05 April 2017
- 稿件说明：
移动端阅览
YU Tongmin, ZHANG Zhengkai, ZOU Dejian. Viscous dissipation effect of polymer melt in a rectangular cross section micro mold channel[J]. CIESC Journal, 2017, (4): 1306-1317.
DOI：

YU Tongmin, ZHANG Zhengkai, ZOU Dejian. Viscous dissipation effect of polymer melt in a rectangular cross section micro mold channel[J]. CIESC Journal, 2017, (4): 1306-1317. DOI： 10.11949/j.issn.0438-1157.20161529.

摘要

基于对微注塑成型过程中聚合物熔体充模流动时黏性耗散效应的理论分析，以聚丙烯（PP）和高密度聚乙烯（HDPE）两种聚合物材料，在不同工艺参数作用下流经不同当量直径和长径比矩形截面微模具通道时，由黏性耗散效应引起的微通道中熔体温度变化进行了试验测量和数值模拟。结果显示，微通道出口熔体温度的试验测量和数值模拟值与理论计算值非常吻合，且其平均误差小于1℃。同时研究发现，增大微模具通道当量直径和长径比时，熔体流动时的黏性耗散热量增多，通道出口熔体温度升高；而当微通道几何尺寸一定时，其黏性耗散热量随注射速度和注射压力的升高而增加，随熔体温度和模具温度的升高而降低；但同样试验条件下，对剪切作用敏感性强的PP材料的黏性耗散热量明显高于对剪切敏感性弱的HDPE材料。

Abstract

Based on the theoretical analysis of viscous dissipation effect when polymer melt flowing in micro injection mold

the change of the melt temperature of the polypropylene (PP) and high density polyethylene (HDPE) caused by the viscous dissipation effect were tested and simulated in the rectangular cross section micro channels with different equivalent diameters and ratios of length to diameter under a variety of process parameters. The results showed that the theoretical calculation and numerical simulation values were highly consistent with the test results

and the average errors were all less than 1℃. The study found that when the equivalent diameter and ratios of length to diameter were increased

the heat of viscous dissipation increased

thus the outlet temperature of channel rose. When the geometry size of the micro channels remains unchanged

the viscous dissipation heat increased with the increase of the injection speed and injection pressure

and decreased with the increase of the melt temperature and mold temperature. But under the same test condition

the viscous dissipation heat of PP material which is more sensitive to shear was obviously higher than that of HDPE.

关键词

Keywords

references

Views

396

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Liquid-liquid mixing characteristics of Bunsen reaction products in microchannels

Numerical simulation of static mixing tubes for HTPB propellant slurry

Study on cooling characteristics of chip array based on microencapsulated phase change material slurry

Performance of manifold microchannel liquid cooling

Two-phase flow simulation and surrogate-assisted optimization of gas film drag reduction in high-concentration coal-water slurry pipeline

Related Author

ZHANG Ke

REN Weijie

WANG Mengna

FAN Kaifeng

CHANG Liping

LI Jiabin

MA Tao

TIAN Jinping

Related Institution

College of Environment and Resources, Taiyuan University of Science and Technology

State Key Laboratory of Clean and Efficient Coal Utilization, Taiyuan University of Technology

Institute of Resources and Environment, Beijing Academy of Science and Technology

School of Chemistry and Chemical Engineering, Nanjing University of Science and Technology

Guangdong Provincial Key Laboratory of Functional Soft Condensed Matter, School of Materials and Energy, Guangdong University of Technology

⁰