Heat transfer process analysis in polymer hollow fiber evaporator

HAN Lei; LIU Jun; XU Kai; LI Bao'an

doi:10.11949/j.issn.0438-1157.20160925

您当前的位置：

首页 >

文章列表页 >

Heat transfer process analysis in polymer hollow fiber evaporator

更新时间：2025-12-10

- Heat transfer process analysis in polymer hollow fiber evaporator
- CIESC Journal Issue 2, Pages: 594-600(2017)
- 作者机构：
  
  1. 化学工程联合国家重点实验室,天津,300072
  2. 天津大学化工学院,天津,300350
  3. 天津化学化工协同创新中心,天津,300072
  4. 天津市膜科学与海水淡化重点实验室,天津,300350
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20160925
  CLC： Q015.2
- Online First：05 February 2017，
  
  Published：05 February 2017
- 稿件说明：
移动端阅览
HAN Lei, LIU Jun, XU Kai, et al. Heat transfer process analysis in polymer hollow fiber evaporator[J]. CIESC Journal, 2017, (2): 594-600.
DOI：

HAN Lei, LIU Jun, XU Kai, et al. Heat transfer process analysis in polymer hollow fiber evaporator[J]. CIESC Journal, 2017, (2): 594-600. DOI： 10.11949/j.issn.0438-1157.20160925.

摘要

蒸发器广泛应用于化工、食品等行业，传统的金属管蒸发器由于其耐酸碱腐蚀性差、表面易结垢等弱点，一定程度上限制了其应用范围，而具有优良性能的高分子中空纤维管可有效解决这些问题，具有很好的应用前景。采用自制的高分子改性中空纤维管，制备出非金属换热器，并进行了蒸发传热实验。结果表明，高分子中空纤维蒸发器的性能与料液温度有密切关系，沸腾进料时蒸发器的传热系数、产水量和热量利用率均高于低温进料；传热热阻主要集中在管外蒸汽加热侧和管壁的导热性能，当沸腾进料时管壁热阻占总传热热阻的66%以上，而管内蒸发侧传热热阻所占比重较低，均低于15.3%，且随着料液流速的增大而降低到5%以下；随着料液温度的降低，蒸发过程的传热系数、能量利用效率以及产水量均显著下降。

Abstract

The evaporator is one of the common heat exchangers

which is widely used in chemical industry and food industry etc. The traditional evaporator with metal tubes is extremely limited in utilization for some reasons that the metal tubes are apt to be corroded by acid or alkali and the serious surface scaling. These problems could be well settled by using excellent performance polymer hollow fibers and good application foreground could be in foresight. In this study

the self-made polymer hollow fibers were used to manipulate the non-metal evaporator and the related evaporation experiments were carried out. The results showed that the performance of the hollow fiber evaporator relied on the thermal conditions of the feed solution. The heat transfer coefficient

the water production and the heat efficiency were better when feed with boiling solution than with low temperature solutions. The heat transfer resistances of fiber walls and the shell side were the main heat transfer resistance. The percentage of the heat transfer resistance with fiber walls can be more than 66% when feed with boiling solution. However

the percentage of heat transfer resistance in the lumen side was as low as 15.3%

and can be lower than 5% when the solution velocity increased. The heat transfer coefficient

the heat efficiency and the water production decreased dramatically when the feed temperature became lower. The results in this study can serve data support for the design and operating parameters optimization of the polymer hollow fiber evaporators

and can promote the further researches and applications of polymer hollow fiber evaporators.

关键词

Keywords

references

Views

393

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Calibration method and experimental validation for resolving inverse heat conduction problem with constant temperature on back surface

Research status and application of functional phase change materials for electro-thermal conversion in thermal energy storage

Heat transfer characteristics of capillary pumping-replenishment evaporation on nanowire clusters surfaces with V-grooves

Modeling method of blast furnace wall temperature field based on steady-state heat transfer analysis

Prediction of heat transfer coefficient of horizontal tube falling film evaporation based on GA-BP neural network

Related Author

ZENG Fubao

CHENG Ruiqin

CHEN Hongchu

LIU Wenjia

DU Ruxue

WANG Siqi

LI Tingxian

WANG Yudan

Related Institution

College of Energy Engineering, Zhejiang University

School of Aeronautics and Astronautics, Zhejiang University

Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University

Liaoning Key Laboratory of Clean Utilization of Chemical Resource, Institute of Chemical Engineering, Dalian University of Technology

Department of Mechanical and Aerospace Engineering, The Hong Kong University of Science and Technology

⁰