Refrigerant desorption characteristics in solid adsorption refrigeration system

LIU Jiaxing; JI Xu; LI Ming; LI Haili; FAN Rongkang; XU Qiangqiang

doi:10.11949/j.issn.0438-1157.20160843

您当前的位置：

首页 >

文章列表页 >

Refrigerant desorption characteristics in solid adsorption refrigeration system

更新时间：2025-11-26

- Refrigerant desorption characteristics in solid adsorption refrigeration system
- CIESC Journal Issue 1, Pages: 336-344(2017)
- 作者机构：
  
  云南师范大学太阳能研究所,云南,昆明,650500
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20160843
  CLC： K511.3
- Online First：05 January 2017，
  
  Published：05 January 2017
- 稿件说明：
移动端阅览
LIU Jiaxing, JI Xu, LI Ming, et al. Refrigerant desorption characteristics in solid adsorption refrigeration system[J]. CIESC Journal, 2017, (1): 336-344.
DOI：

LIU Jiaxing, JI Xu, LI Ming, et al. Refrigerant desorption characteristics in solid adsorption refrigeration system[J]. CIESC Journal, 2017, (1): 336-344. DOI： 10.11949/j.issn.0438-1157.20160843.

摘要

搭建了以活性炭-甲醇为工质对的单床吸附式制冷实验系统，对圆柱形吸附管内的吸附剂在不同解吸温度和不同解吸时间条件下的解吸量进行实验研究。解吸温度分别为84、89、94℃，解吸时间分别为4、5、6、7 h。实验结果表明，解吸温度、解吸时间和制冷剂的解吸量对吸附式制冷系统制冷循环性能有着重要影响。在热源温度为84℃加热时间4 h时，系统的制冷性能系数COP最小为0.053。系统在解吸温度为94℃，解吸时间为6 h时，系统的制冷性能系数COP最大为0.19，此时的解吸温度和解吸时间为最佳解吸温度和解吸时间。继续增加解吸时间，解吸量的增长率小于耗能的增长率，COP减小。

Abstract

A single-bed adsorption refrigeration experimental system with the working-pair of activated carbon-methyl alcohol was built.And investigations on the effect of desorption temperature and desorption time on the desorption amount of refrigerant in cylindrical adsorption tube were conducted.The desorption temperature was set at 84

89 and 94℃

and the desorption was last for 4

6 and 7 h

respectively.The experimental results indicate that desorption temperature

desorption time and the desorption amount of refrigerant had significant effect on the refrigeration recycling performance of the adsorption refrigeration system.The minimum coefficient of performance(COP) of 0.053 was achieved when the heating resource temperature was maintained at 84℃ and the heating time was 4 h.The maximum COP of 0.19 was achieved when the desorption temperature was maintained at 94℃ and desorption time was 6 h.Consequently

94℃ and 6 h were recommended as the optimal desorption temperature and desorption time.If the desorption time was continuously increased to be more than 6 h

the increasing rate of desorption amount would be less than that of energy consumption

then COP will consequently decrease.

关键词

Keywords

references

Views

192

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Heat storage performance of composite adsorbent with activated carbon fiber

Preparation of amino modified styrene-divinylbenzene resin and its adsorption of rhenium

Adsorption and desorption of tungsten ions in water by morpholine chelate resin

Theoretical analysis and experiment of thermochemical composite sorption heat storage cycle

Performance analysis of combined adsorption refrigeration and seawater desalination system

Related Author

Weili LUO

Wenwen WANG

Quanwen PAN

Tianshu GE

Ruzhu WANG

Yu ZHANG

Rong HUA

Xiaokang KOU

Related Institution

School of Mechanical Engineering, Shanghai Jiao Tong University

State Key Laboratory of Nuclear Resources and Environment, School of Nuclear Science and Engineering, East China University of Technology

Sunresin New Materials Co., Ltd

Department of Applied Chemistry, Zhejiang Gongshang University

School of Environmental Science and Engineering, Zhejiang Gongshang University

⁰