Working characteristic modeling and analysis for single screw compressor with multicolumn envelope meshing pair

WANG Zengli; SHEN Yingfeng; WANG Zhenbo; WANG Jun; FENG Quanke

doi:10.11949/j.issn.0438-1157.20160718

您当前的位置：

首页 >

文章列表页 >

Working characteristic modeling and analysis for single screw compressor with multicolumn envelope meshing pair

更新时间：2025-11-26

- Working characteristic modeling and analysis for single screw compressor with multicolumn envelope meshing pair
- CIESC Journal Issue 1, Pages: 215-222(2017)
- 作者机构：
  
  1. 中国石油大学(华东)化学工程学院,山东,青岛,266580
  2. 西安交通大学能源与动力工程学院,陕西,西安,710049
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20160718
  CLC： H45
- Online First：05 January 2017，
  
  Published：05 January 2017
- 稿件说明：
移动端阅览
WANG Zengli, SHEN Yingfeng, WANG Zhenbo, et al. Working characteristic modeling and analysis for single screw compressor with multicolumn envelope meshing pair[J]. CIESC Journal, 2017, (1): 215-222.
DOI：

WANG Zengli, SHEN Yingfeng, WANG Zhenbo, et al. Working characteristic modeling and analysis for single screw compressor with multicolumn envelope meshing pair[J]. CIESC Journal, 2017, (1): 215-222. DOI： 10.11949/j.issn.0438-1157.20160718.

摘要

多圆柱复合包络型面具有复杂的三维空间结构，是影响单螺杆压缩机性能的重要因素。为了研究多圆柱复合包络型面单螺杆压缩机的工作特性，建立了多圆柱复合包络型面压缩机的几何特性数值分析模型，利用上述模型，对比分析了多圆柱复合包络型面和单直线包络型面对单螺杆压缩机几何特性及热力学性能的影响。结果表明：多圆柱复合包络型面的采用使得实际星轮齿宽会随星轮转角的变化而变化，且均大于单直线型面星轮齿宽；受星轮齿宽变化的影响，任意星轮转角位置处，多圆柱复合包络型面单螺杆压缩机工作腔容积增大，最大基圆容积增大5.2%，工作腔内部压力减小。多圆柱复合包络型面单螺杆压缩机封闭螺旋线更靠近进气端，排气孔口起始位置更靠近排气端，导致排气过程延迟，排气过程流动阻力损失增加。通过上述工作，可为新型多圆柱复合包络型面单螺杆压缩机的设计及结构优化提供理论依据。

Abstract

The multicolumn envelope meshing pair(MEMP) is the important factor that affects the performance of single screw compressor due to its complex three-dimensional structure.In order to study the working characteristic of the single screw compressor with MEMP

a geometric features numerical calculation model is set up.By using this mathematical model

the effects of the MEMP and the straight line envelope meshing pair(LEMP) on the geometric features and the thermal dynamic performances are compared.Analysis results show that the use of the MEMP makes the actual star-wheel tooth width changing along with the star-wheel angle larger than that of the star-wheel with LEMP.Affected by the change of star-wheel tooth width

the working chamber volume of the compressor with MEMP will increase

the cavity internal pressure will decrease at the same star-wheel angle

and the largest base volume will be increased 5.2%.The closed spiral will be closer to the inlet side and the exhaust orifice spiral will be closer to the exhaust end for the compressor with MEMP which will lead to the delay of the exhaust process and more flow resistance losses.All analysis results obtained can provide the theory basis for optimum design of the single screw compressor with multicolumn envelope meshing pair.

关键词

Keywords

references

Views

287

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Application of adaptive algorithm of online reduced KECA in fault detection

Performance analysis of absorption heat recovering cycle with high-pressure booster using NH3-LiNO3 as the working pair

Online adaptive wavelength selection method and its application in gasoline blending process

Configuration analysis of integrated thermal management about high altitude long-endurance unmanned aerial vehicle

Influence of channel height on resistance characteristics in triangular grooved channel by pulsating flow

Related Author

Jinyu GUO

Wentao Li

Yuan LI

Erjian CHEN

Yanjun DAI

Kai WANG

Jian LONG

Wenli DU

Related Institution

College of Information Engineering, Shenyang University of Chemical Technology

Institute of Refrigeration and Cryogenics, Shanghai Jiao Tong University

School of Information Science and Engineering, East China University of Science and Technology

Key Laboratory of Advanced Control and Optimization for Chemical Processes, Ministry of Education, East China University of Science and Technology

State Key Laboratory of Chemical Engineering, East China University of Science and Technology

⁰