Numerical simulation of droplet impact on hybrid surfaces with different wettabilities

CHEN Yuanyuan; XU Jinliang; LI Jiwei

doi:10.11949/j.issn.0438-1157.20160662

您当前的位置：

首页 >

文章列表页 >

Numerical simulation of droplet impact on hybrid surfaces with different wettabilities

更新时间：2025-11-26

- Numerical simulation of droplet impact on hybrid surfaces with different wettabilities
- CIESC Journal Issue 12, Pages: 5006-5014(2016)
- 作者机构：
  
  华北电力大学能源动力与机械工程学院,北京,102206
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20160662
  CLC： K124
- Online First：05 December 2016，
  
  Published：05 December 2016
- 稿件说明：
移动端阅览
CHEN Yuanyuan, XU Jinliang, LI Jiwei. Numerical simulation of droplet impact on hybrid surfaces with different wettabilities[J]. CIESC Journal, 2016, (12): 5006-5014.
DOI：

CHEN Yuanyuan, XU Jinliang, LI Jiwei. Numerical simulation of droplet impact on hybrid surfaces with different wettabilities[J]. CIESC Journal, 2016, (12): 5006-5014. DOI： 10.11949/j.issn.0438-1157.20160662.

摘要

采用VOF方法对液滴碰撞亲-疏水性组合壁面过程进行数值模拟。通过量纲1化，在Reynolds数不变的情况下，研究Weber数和亲水性区域直径对液滴碰撞动态特性的影响，绘制了液滴碰撞结果分区图。结果表明：随着Weber数从1增加至100，液滴呈现出附着、短液滴一次破碎和长液滴多次破碎3种状态；液滴破碎过程受到表面张力、壁面黏附力及Rayleigh不稳定性的影响，亲水性区域直径增加时，液滴破碎所对应的临界Weber数随之增大；此外，Weber数较大时，液滴最大铺展因子不受亲水性区域直径的影响，Weber数较小时，最大铺展因子随亲水性区域直径的增大而增大。

Abstract

Surfaces with patterned domains of different wettabilities can be used for controlling the impact process. The dynamic behavior of droplet impact on hybrid surfaces with different wettabilities is simulated using the VOF method by dimensionless. Effects of Weber number and hydrophilic region diameter are studied with constant Reynold number. A drop impact regime map is generated

in which the impact dynamics is characterized as a function of Weber number and relative diameter of hydrophilic region. With the increase of Weber number

the droplet presents three different status: deposition

pinch-off as a short liquid column and break up as a long liquid column. The threshold Weber number where pinch-off occurs will increase with the increase of hydrophilic region diameter. For high Weber number

the maximum spreading factors are the same for different hydrophilic region diameter. While for low Weber number

the maximum spreading factors will increase with it.

关键词

Keywords

references

Views

324

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Numerical simulation of droplet impinging and freezing on cold surfaces with different wettability

Simulation of loop heat pipe start-up characteristic

Model of charge/discharge operation for all-vanadium redox flow battery

Simulation and optimization of sinter circular cooler layer-loading

Prediction study on bond strength and modulus of fused deposition modeling product

Related Author

LENG Mengyao

CHANG Shinan

DING Liang

HUANG Jie

WANG Naihua

CHENG Lin

LI Minghua

FAN Yongsheng

Related Institution

School of Aeronautics Science and Engineering, Beihang University

Institute of Thermal Science and Technology, Shandong University

Department of Chemical Engineering, State Key Laboratory of Chemical Engineering, Tsinghua University

1School of Energy Science and Engineering，Central South University

Zhongye Changtian International Engineering Co.，Ltd.

⁰