Drag reduction of superhydrophobic microchannels based on parabolic gas-liquid interfaces

LI Chunxi; ZHANG Shuo; XUE Quanxi; YE Xuemin

doi:10.11949/j.issn.0438-1157.20160629

您当前的位置：

首页 >

文章列表页 >

Drag reduction of superhydrophobic microchannels based on parabolic gas-liquid interfaces

更新时间：2025-11-26

- Drag reduction of superhydrophobic microchannels based on parabolic gas-liquid interfaces
- CIESC Journal Vol. 67, Issue 10, Pages: 4126-4134(2016)
- 作者机构：
  
  华北电力大学电站设备状态监测与控制教育部重点实验室,河北,保定,071003
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20160629
  CLC： 35
- Online First：05 October 2016，
  
  Published：05 October 2016
- 稿件说明：
移动端阅览
LI Chunxi, ZHANG Shuo, XUE Quanxi, et al. Drag reduction of superhydrophobic microchannels based on parabolic gas-liquid interfaces[J]. CIESC Journal, 2016, 67(10): 4126-4134.
DOI：

LI Chunxi, ZHANG Shuo, XUE Quanxi, et al. Drag reduction of superhydrophobic microchannels based on parabolic gas-liquid interfaces[J]. CIESC Journal, 2016, 67(10): 4126-4134. DOI： 10.11949/j.issn.0438-1157.20160629.

摘要

针对超疏水表面微通道中的流动减阻特性，基于抛物线形气-液界面假设，采用VOF模型模拟了微通道中的二维层流流动，分析了流动和结构参数对减阻效果的影响。结果表明，含矩形微坑的超疏水表面微通道具有显著减阻作用，fRe随Reynolds数增大而略有提高，量纲1压降比随入口速度增大而略有下降。当增大微坑面积比或减小微通道高度时，fRe减小，量纲1压降比增大；且微通道高度越小，微坑面积比对fRe的影响越显著。随抛物线形高度增加，压降比和滑移长度均线性减小，而fRe则线性增加。当微坑深度大于其宽度的40%时，压降比和滑移长度趋于定值。微坑形状对减阻效果的影响依次是燕尾形、矩形、梯形和三角形。

Abstract

Based on the model of volume of fluid

two-dimensional fluid laminar flow in superhydrophobic microchannels was numerically simulated with given parabolic gas-liquid interfaces. The effects of several flow and structural parameters on fRe

the normalized slip length and pressure drop were investigated. The results show that superhydrophobic microchannels with rectangular microcavities exhibited significant drag reduction in a way that fRe increased slightly with increase of Reynolds number whereas normalized pressure drop decreased slightly with increase of inlet velocity. When the area ratio of microcavities was increased or the microchannel diameter was decreased

fRe was reduced but normalized pressure drop was enhanced. In case of small microchannel diameter

the area ratio of microcavities significantly affected fRe. With increase of the parabolic height

the ratio of normalized pressure drop and the normalized slip length decreased linearly

however fRe increased linearly. The impact of microcavities on the normalized slip length and the ratio of normalized pressure drop was minimal provided that the microcavity depth was greater than 40% of its width. The dovetail microcavities exhibited the greatest effect on drag reduction

followed by the rectangular

trapezoidal

triangular microcavities in the order of high to low.

关键词

Keywords

references

Views

222

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Liquid-liquid mixing characteristics of Bunsen reaction products in microchannels

Entropy analysis of CO2-air microchannel evaporator in two-phase flow region

Review of research on liquid cooling technology for data centers

Synergistic mechanism in open microchannel and jet impingement hybrid cooling system

A two-stage dual-channel deep learning model for chemical fault classification

Related Author

ZHANG Ke

REN Weijie

WANG Mengna

FAN Kaifeng

CHANG Liping

LI Jiabin

MA Tao

TIAN Jinping

Related Institution

College of Environment and Resources, Taiyuan University of Science and Technology

State Key Laboratory of Clean and Efficient Coal Utilization, Taiyuan University of Technology

Institute of Resources and Environment, Beijing Academy of Science and Technology

School of Environment and Architecture, University of Shanghai for Science and Technology

School of Environmental and Energy Engineering, Beijing University of Civil Engineering and Architecture

⁰