Numerical simulation of droplet impinging and freezing on cold surfaces with different wettability

LENG Mengyao; CHANG Shinan; DING Liang

doi:10.11949/j.issn.0438-1157.20151888

您当前的位置：

首页 >

文章列表页 >

Numerical simulation of droplet impinging and freezing on cold surfaces with different wettability

更新时间：2025-11-26

- Numerical simulation of droplet impinging and freezing on cold surfaces with different wettability
- CIESC Journal Issue 7, Pages: 2784-2792(2016)
- 作者机构：
  
  北京航空航天大学航空科学与工程学院,北京,100191
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20151888
  CLC： K01O359.1
- Online First：05 July 2016，
  
  Published：05 July 2016
- 稿件说明：
移动端阅览
LENG Mengyao, CHANG Shinan, DING Liang. Numerical simulation of droplet impinging and freezing on cold surfaces with different wettability[J]. CIESC Journal, 2016, (7): 2784-2792.
DOI：

LENG Mengyao, CHANG Shinan, DING Liang. Numerical simulation of droplet impinging and freezing on cold surfaces with different wettability[J]. CIESC Journal, 2016, (7): 2784-2792. DOI： 10.11949/j.issn.0438-1157.20151888.

摘要

对冷水滴撞击不同表面时的动力学行为和相变过程进行了模拟。通过耦合VOF和Level-set方法追踪气液自由界面，结合焓-孔隙度相变模型，模拟水滴撞击冷表面的动力学行为及相变特征。选取亲水（接触角30°）、疏水（接触角114°）和超疏水（接触角163°）3种典型浸润性的表面，计算了多种壁温条件下的水滴撞击结冰过程。结果表明提高表面疏水性，将减小水滴与冷表面的接触时间和接触面积，降低水滴内的相变速率，延缓水滴结冰的时间。在表面温度高于-15℃时，超疏水表面可以避免冷水滴的冻结黏附，保持表面洁净。将模拟得到的最大铺展直径、回缩速率以及冻结情况，与已有实验结果进行对比验证，表明了模拟方法的有效性和准确性。

Abstract

A strategy is presented to simulate the impact and solidification of the water droplet on different substrates. Simulations were performed using a coupled volume-of-fluid and level-set method to tracking the air-water interface and an enthalpy-porosity method to capture the phase transition. Three surface types were investigated: hydrophilic surface (contact angle 30°)

hydrophobic surface (contact angle 114°) and superhydrophobic surface (contact angle 163°). The results showed that decreasing the wettability would reduce the contact time and area with the cold surface

and delay the freezing of the droplet. When temperature of the surface is higher than -15℃

the superhydrophobic surface can remain entirely ice-free under the simulated conditions. By comparing the maximum droplet spread

retraction response and time for solidification with the experimental results

the effectiveness and precision of the simulation strategy were demonstrated.

关键词

Keywords

references

Views

506

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Numerical simulation of pulsating heat pipes with two-bends in different structures

Effect of cooled cylindrical surface on droplet dynamic behavior

Study on flash evaporation characteristics as well as thermodynamic variation performance in liquid hydrogen tank during on-orbit venting

Study on enhanced pool boiling heat transfer based on self-driven jet device

Numerical study on heat and mass transfer characteristics of particle coating in a spray fluidized bed with draft plates

Related Author

Erhui JIANG

Dongwei ZHANG

Junjie ZHOU

Chao SHEN

Xinli WEI

Xin ZHOU

Ledong DENG

Hong WANG

Related Institution

Research Center on the Technology and Equipments for Energy Saving in Thermal Energy System of MOE, School of Chemical Engineering and Energy, Zhengzhou University

School of Civil Engineering, Zhengzhou University

Institute of Engineering Thermophysics

Key Laboratory of Low-Grade Energy Utilization Technologies & Systems, MOE, Chongqing University

Department of Refrigeration and Cryogenic Engineering, Xi’an Jiaotong University

⁰