Discrete modeling of discharge dynamics of granular material in moving bed: effect of outlet setting

XIAO Xiao; SU Jinglin; XU Guangwen; CUI Lijie; LIU Xiaoxing

doi:10.11949/j.issn.0438-1157.20151714

您当前的位置：

首页 >

文章列表页 >

Discrete modeling of discharge dynamics of granular material in moving bed: effect of outlet setting

更新时间：2025-12-10

- Discrete modeling of discharge dynamics of granular material in moving bed: effect of outlet setting
- CIESC Journal Issue 5, Pages: 1710-1718(2016)
- 作者机构：
  
  1. 中国科学院大学研究生院,北京,100049
  2. 辽宁科技大学化学工程学院,辽宁,鞍山,114051
  3. 中国科学院过程工程研究所,北京,100090
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20151714
  CLC： Q018
- Online First：05 May 2016，
  
  Published：05 May 2016
- 稿件说明：
移动端阅览
XIAO Xiao, SU Jinglin, XU Guangwen, et al. Discrete modeling of discharge dynamics of granular material in moving bed: effect of outlet setting[J]. CIESC Journal, 2016, (5): 1710-1718.
DOI：

XIAO Xiao, SU Jinglin, XU Guangwen, et al. Discrete modeling of discharge dynamics of granular material in moving bed: effect of outlet setting[J]. CIESC Journal, 2016, (5): 1710-1718. DOI： 10.11949/j.issn.0438-1157.20151714.

摘要

采用离散单元法(DEM)模拟研究了二维移动床出口设置对物料卸料特性的影响。为验证模拟结果的合理性

首先针对单出口移动床进行了模拟研究

模拟结果表明:出口处颗粒质量流率满足修正的Beverloo经验关系式

而且定性上物料层内部流动区宽度随出口宽度的变化规律与实验结果吻合良好。在此基础上对两出口移动床的卸料特性进行了研究

得到以下结论:当出口宽度相等时

物料层内流动区宽度等于单出口条件下流动区宽度、出口间距及出口宽度的加和

而且每个出口处颗粒质量流率与单出口条件下颗粒质量流率相当;当出口宽度不相等时

增加大出口的宽度或减小出口之间的距离有助于提高小出口处颗粒质量流率

但大出口处颗粒质量流率基本保持恒定

不受小出口影响。

Abstract

The influence of outlet setting on the discharge dynamics of granular material in 2D moving beds was investigated by conducting discrete element simulations. To validate the simulation

a moving bed with single outlet was first modeled. The simulation results showed that the variation of discharge rate was tally with the modified Beverloo

and the variation tendency of the width of funnel zone was in agreement with the experimental data. Based on such validation

the discharge characteristics of granular material in the moving bed with two outlets were then systematically investigated. The simulation results indicated that as to the bed with two same size outlets

the width of funnel zone was simply equal to the sum of the width of funnel zone of the moving bed with one same size outlet

the distance between outlets and the width of outlet

and the granular mass discharge rate was roughly equivalent to that of the moving bed with one same size outlet. For the bed with two different size outlets

increasing the width of large outlet or decreasing the outlet distance was conducive to increasing the discharge rate at small outlet. Nevertheless

the discharge rate at large outlet was not influenced by the small outlet and nearly kept constant.

关键词

Keywords

references

Views

294

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Flow and heat transfer characteristics of particles flowing along the plate with different mixing elements

Numerical investigation on flow and heat transfer performance of gravity-driven granular flowing across inverted drop-shaped tube

Effect of introducing large additive particles on flow characteristics in radial flow moving bed

Phenomenon of pinning in trapezoidal moving beds with cross-flow

Mixed matrix membranes based on nitrogen-rich Schiff base network polymer and their CO2 separation performance

Related Author

TIAN Xing

ZHANG Jiayue

GUO Zhigang

YANG Jian

WANG Qiuwang

Zhoutuo TAN

Zhigang GUO

Jian YANG

Related Institution

Key Laboratory of Thermo-Fluid Science and Engineering, Ministry of Education, Xi'an Jiaotong University

Key Laboratory of Thermo-Fluid Science and Engineering, Ministry of Education, Xi’an Jiaotong University, , Shaanxi

State Key Laboratory of Heavy Oil, China University of Petroleum(Beijing)

College of Petrochemical Engineering, Liaoning Shihua University

College of Chemical Engineering, China University of Petroleum

⁰