Performance analysis of hydrodynamic mechanical seals based on self-pumping principle

ZHOU Min; SUN Jianjun; MA Chenbo; YU Qiuping; ZHOU Peiyan

doi:10.11949/j.issn.0438-1157.20141035

您当前的位置：

首页 >

文章列表页 >

Performance analysis of hydrodynamic mechanical seals based on self-pumping principle

更新时间：2025-12-10

- Performance analysis of hydrodynamic mechanical seals based on self-pumping principle
- CIESC Journal Issue 2, Pages: 687-694(2015)
- 作者机构：
  
  南京林业大学机械电子工程学院,江苏,南京,210037
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20141035
  CLC： H136
- Online First：05 February 2015，
  
  Published：05 February 2015
- 稿件说明：
移动端阅览
ZHOU Min, SUN Jianjun, MA Chenbo, et al. Performance analysis of hydrodynamic mechanical seals based on self-pumping principle[J]. CIESC Journal, 2015, (2): 687-694.
DOI：

ZHOU Min, SUN Jianjun, MA Chenbo, et al. Performance analysis of hydrodynamic mechanical seals based on self-pumping principle[J]. CIESC Journal, 2015, (2): 687-694. DOI： 10.11949/j.issn.0438-1157.20141035.

摘要

基于离心泵工作原理提出了一种自泵送流体动压型机械密封

并运用Fluent软件对自泵送型槽进行了三维流场动力学仿真分析

探讨了几何参数和工况参数对自泵送流体动压型机械密封性能即端面开启力和泄漏率的影响。研究结果表明:转速增大

开启力和泄漏率均减小;介质压力、槽台宽比、引流孔孔径及螺旋角增大

开启力和泄漏率均增大;随着槽数、槽长坝长比的增大

开启力均有所降低

泄漏率略有增大;槽深对开启力和泄漏率的影响趋势相似

存在一个使开启力较大而泄漏率较小的槽深;通过型槽参数匹配

自泵送流体动压型机械密封可以获得足够的开启力和较低的泄漏率。

Abstract

A kind of self-pumping hydrodynamic mechanical seal was presented based on the principle of centrifugal pump. The three-dimensional flow fields of self-pumping grooves were analyzed using Fluent

and the influences of geometric parameters and operating parameters on the sealing properties

including opening force and leakage rate were also discussed. Leakage rate and opening force decreased with increasing speed

and increased with increasing pressure

aperture diameter

helix angle and the ratio of groove width and ridge width. With increasing groove number

ratio of groove length and dam length

opening force decreased and leakage rate increased slightly. The influence of groove depth on opening force was similar to the influence on leakage rate

and there existed an optimal groove depth which could achieve higher opening force and lower leakage rate. Consequently

the self-pumping hydrodynamic mechanical seal proposed could get larger opening force and lower leakage rate by matching groove parameters.

关键词

Keywords

references

Views

413

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Intelligent optimization and deformation analysis of novel flexible dam foil face gas seal

Heat transfer characteristics of coaxial tubes type deep borehole heat exchanger in water-rich geothermal reservoir

Heat and mass transfer based feed bottleneck identification and reengineering of multi-feed demethanizer in ethylene complex

Computer simulation of mechanical properties of polymer materials

ASME large spherical tank based on finite element analysis

Related Author

LI Yushi

CHEN Yuan

LI Yuntang

PENG Xudong

WANG Bingqing

LI Xiaolu

Jiuchen MA

Feiyu YI

Related Institution

College of Mechanical and Electrical Engineering, China Jiliang University

College of Mechanical Engineering, Zhejiang University of Technology

School of Energy and Safety Engineering, Tianjin Cheng Jian University

Key Laboratory for Efficient Use of Low and Medium Grade Energy, Ministry of Education, Tianjin University

Research Center for Efficient Utilization Technology of Geothermal Energy, Tianjin Chengjian University

⁰