Influence of substrate thickness on temperature distribution along surface of drying droplets

ZHANG Kai; WANG Yilin; XU Xuefeng

doi:10.11949/j.issn.0438-1157.20140745

您当前的位置：

首页 >

文章列表页 >

Influence of substrate thickness on temperature distribution along surface of drying droplets

更新时间：2025-12-10

- Influence of substrate thickness on temperature distribution along surface of drying droplets
- CIESC Journal Issue 2, Pages: 703-708(2015)
- 作者机构：
  
  北京林业大学工学院,北京,100083
- 作者简介：
- 基金信息：
- DOI：10.11949/j.issn.0438-1157.20140745
  CLC： K124
- Online First：05 February 2015，
  
  Published：05 February 2015
- 稿件说明：
移动端阅览
ZHANG Kai, WANG Yilin, XU Xuefeng. Influence of substrate thickness on temperature distribution along surface of drying droplets[J]. CIESC Journal, 2015, (2): 703-708.
DOI：

ZHANG Kai, WANG Yilin, XU Xuefeng. Influence of substrate thickness on temperature distribution along surface of drying droplets[J]. CIESC Journal, 2015, (2): 703-708. DOI： 10.11949/j.issn.0438-1157.20140745.

摘要

蒸发液滴的表面温度分布对液滴的液体流动和颗粒沉积有着重要的影响。获得液滴表面温度目前主要采用数值计算方法。针对有限厚度基底上的蒸发液滴

分析了网格划分对液滴表面温度计算结果的影响。结果表明

相比于液滴边缘附近区域

液滴中心区域网格的细化对计算结果影响不大;而在接触线附近

相比于网格尺寸

网格细化区域大小对计算结果的影响也很小。利用数值方法研究了基底厚度对蒸发液滴表面温度分布特性的影响

发现随着基底厚度的改变液滴表面出现3种温度分布模式:(1)从液滴顶点到边缘处表面温度逐渐升高;(2)液滴表面温度非单调变化;(3)从液滴顶点到边缘处表面温度逐渐降低。考虑热传导路径长度和蒸发制冷的共同作用

对不同表面温度分布模式进行了解释

并获得了(hR

q)坐标平面上的表面温度分布模式相图。本文结果将有助于对液滴蒸发过程的理解

并为蒸发诱导自组装、喷墨印刷等技术提供理论依据。

Abstract

The temperature distribution along the surface of drying droplet has significant influence on fluid flow and particle deposition of the droplet. Currently

the surface temperature distribution of the droplet is often studied by numerical methods. For drying droplets on finite thickness substrates

the effect of meshing on calculated surface temperature is discussed. Compared to the region near the droplet edge

mesh refinement in the central region of the droplet has negligible effect on numerical results. The influence of the size of mesh refinement region near the droplet edge on droplet surface temperature can also be neglected compared to the level of mesh refinement. By studying the effects of relative substrate thickness hR on droplet surface temperature

three different states with changing substrate thickness are found. (1) From center to edge

surface temperature increases monotonically. (2) From center to edge

surface temperature changes non-monotonically. (3) From center to edge

surface temperature decreases monotonically. The different patterns of droplet surface temperature can be explained by considering the combined effects of heat conduction path length and evaporative cooling. The surface temperature "phase diagram" on parameters (hR

q) with different relative thermal conductivities is obtained. The results will be helpful to understanding droplet evaporation and providing theoretical basis for evaporation induced self-assembly and ink jet printing.

关键词

Keywords

references

Views

346

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

A multiscale approach for the thermo-mechanical coupling analysis of parallel-flow PCHE core

Research on solidification characteristics of particles formed by dropping molten polyethylene glycol into oil pool

Investigation on the dynamics and vaporization characteristics of droplet impact on the heated wall surface

Heat transfer characteristics of oblique droplet impact on liquid film

Simulation research on the boiling heat transfer characteristics of liquid sodium under microgravity

Related Author

WANG Hao

CAI Lujun

BAI Fan

ZHANG Feng

ZHENG Zhangjing

YANG Qingyun

YAN Shixing

SHI Yuchen

Related Institution

School of Science, Wuhan University of Science and Technology

Hubei Province Key Laboratory of Systems Science in Metallurgical Process

Hubei Key Laboratory for Engineering Structural Analysis and Safety Assessment

School of Mechanical Engineering, Wuhan University of Science and Technology

School of Low-carbon Energy and Power Engineering, China University of Mining and Technology

⁰