Optimization of injection velocity profile in injection molding based on cavity pressure

LI Chuang; WANG Fuli; LIU Yang; CHANG Yuqing

您当前的位置：

首页 >

文章列表页 >

Optimization of injection velocity profile in injection molding based on cavity pressure

更新时间：2025-12-10

- Optimization of injection velocity profile in injection molding based on cavity pressure
- CIESC Journal Issue 5, Pages: 1163-1168(2010)
- 作者机构：
  
  1. 东北大学信息科学与工程学院
  2. 东北大学流程工业综合自动化教育部重点实验室
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Online First：05 May 2010，
  
  Published：05 May 2010
- 稿件说明：
移动端阅览
LI Chuang, WANG Fuli, LIU Yang, et al. Optimization of injection velocity profile in injection molding based on cavity pressure[J]. CIESC Journal, 2010, (5): 1163-1168.
DOI：

LI Chuang, WANG Fuli, LIU Yang, et al. Optimization of injection velocity profile in injection molding based on cavity pressure[J]. CIESC Journal, 2010, (5): 1163-1168. DOI：

摘要

注塑成型中，把熔前速度恒定（熔体均匀填充模具）作为设定注射速度参数的重要依据。针对熔前速度无法测量问题，提出对于一类注塑制品，用模腔压力随时间线性增加来近似熔前速度恒定。其次，利用实验数据，设计并建立了模腔压力递归神经网络(RNN)模型。在此基础上，提出一种注射速度设定曲线的分级优化策略，其中曲线分级是利用Douglas-Peucker方法自动确定速度分级数目和位置，优化过程则采取基于滑动窗口的迭代优化方法来实现。实验结果表明，该优化方法可以根据模腔复杂程度自动选择合适的注射曲线分级数目，并且其优化精度较常规等间隔分级优化方法更高。

Abstract

Uniform melt front (MFV) velocity throughout the filling of the mold cavity is recommended as the design criterion for injection profile.Due to the difficulty of measuring MFV

a criterion that cavity pressure followed a ramp with time was proposed as an approximate substitute to constant MFV in this study.Then a recurrent neural network was developed for estimating the cavity pressure from online measurable variables

based on which the profile problem was transformed to an optimization problem for the predicted cavity pressure to track a given ramp.Subsequently the velocity profile was treated as a piecewise ramp one with respect to the increment of screw stroke

and its turning points and the slopes of each section were the optimization variables.The Douglas-Peucker method was introduced to determine the number and positions of separation points of the profile and an iterative optimization method with sliding window was presented to solve the optimization problem.Experimental results showed that this optimization method could automatically give the number of pieces of injection velocity profile and its precision of optimization was higher than the regular optimization method with equal fixed intervals.

关键词

Keywords

references

Views

418

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Study on impact of impurities in coal chemical waste salt on solvation of NaCl and Na2SO4

Heat transfer mechanisms, bottleneck identification and optimization in heat exchanger networks under variable operating conditions

Advantages and risks of swirling cooling granulation towers

A hybrid modeling and optimization strategy for sequential simulated moving bed

Effect of belt structure design on the vulcanization characteristics of all-steel radial tires

Related Author

No data

Related Institution

No data

⁰