Properties of non-metallic powder recycled from paper-based printed circuit boards and performance of composites

WANG Xinjie; GUO Yuwen; ZHANG Jianqiang; QIAO Qi; LIU Jingyang

您当前的位置：

首页 >

文章列表页 >

Properties of non-metallic powder recycled from paper-based printed circuit boards and performance of composites

更新时间：2025-12-10

- Properties of non-metallic powder recycled from paper-based printed circuit boards and performance of composites
- CIESC Journal Issue 3, Pages: 795-800(2010)
- 作者机构：
  
  1. 中国环境科学研究院
  2. 西南交通大学环境科学与工程学院
- 作者简介：
- 基金信息：
- DOI：
  CLC：
- Online First：05 March 2010，
  
  Published：05 March 2010
- 稿件说明：
移动端阅览
WANG Xinjie, GUO Yuwen, ZHANG Jianqiang, et al. Properties of non-metallic powder recycled from paper-based printed circuit boards and performance of composites[J]. CIESC Journal, 2010, (3): 795-800.
DOI：

WANG Xinjie, GUO Yuwen, ZHANG Jianqiang, et al. Properties of non-metallic powder recycled from paper-based printed circuit boards and performance of composites[J]. CIESC Journal, 2010, (3): 795-800. DOI：

摘要

利用电镜扫描、X射线荧光光谱和红外光谱分析废纸基PCBs非金属粉以及对复合材料力学性能和热性能测试，研究了废纸基PCBs非金属粉性质及对复合材料性能的影响，结果表明：废纸基PCBs中含少量玻璃纤维，绝大多数是树脂聚合物，颗粒表面存在羟基、羰基、缩醛基、硅醇基等官能团，是极性材料；非金属粉经改性后与基体PP混合表现出很好的相容性，有效提高复合材料弯曲强度和维卡软化温度（VST），增加复合材料的阻燃性能；复合材料弯曲强度随非金属粉添加量增加而增大，0.08 cm（180目）非金属粉添加量30％时可提高弯曲强度9.1 MPa，VST约提高2℃；小颗粒非金属粉有利于复合材料性能改善，可作为填料制作PP复合材料。

Abstract

The non-metallic powder recycled from waste paper-based printed circuit boards (PCBs) was analyzed with scanning electron microscopy (SEC)

X-ray fluorescence (XRF)

Fourier transform infrared spectrum (FTIR)

and the mechanical properties

heat resistance of the non-metallic powder filled polypropylene (PP) composites were tested. The properties of non-metallic powder recycled from waste paper-based PCBs and its effect on the performance of the composites were studied. The results showed that the waste paper-based PCBs was resin polymer with a little fiberglass

and its polarity was due to the presence of hydroxide groups

carbonyl groups

acetal groups and silanol groups on the particle surface. Modified non-metallic powder and PP powder in the composite exhibited excellent compatibility

and modified non-metallic powder enhanced the bending strength

Vicat softening temperature (VST) and flame retardance capability of the composite. The bending strength of the composite increased with increasing filler proportion of the nonmetal powder

bending strength increased by 9.1 MPa and VST rose by 2℃ when the 0.08 cm（180 mesh） non-metallic powder filler proportion reached 30%. The non-metallic powder could be used as filler in the PP composite to improve the properties of the composite.

关键词

Keywords

references

Views

506

下载量

CSCD

Alert me when the article has been cited

提交

Tools

Publicity Resources

Tribological properties of PPTA-pulp reinforced NBR composites

Property and microstructure of ABS composite modified with salt sulfate whisker

Effect of DMDBX on crystalline structure and properties of PP

Mechanical and magnetic properties of poly（phenylene sulfide）/Fe3O4 composites

Interface of C/Al composite prepared by stir casting process

Related Author

DING Jianning

YOU Xiulan

LI Jinchun

ZUO Wenwen

周健

NI Zhuo

NIU Ke

XI Wenying

Related Institution

上海兰邦工业纤维有限公司

江苏工业学院材料科学与工程学院

江苏技术师范学院应用材料研究所

深圳大学化学与化工学院

江苏省环境材料与工程重点实验室

⁰