Study of thermal-fluid-solid coupling on dynamic characteristics of oil-gas miscible backflow pumping seal

doi:10.11949/0438-1157.20191026

Abstract

Abstract:

The dynamic characteristics of oil-gas two-phase dynamic pressure seal were studied. The oil-gas two-phase Reynolds equation was established based on the Reynolds equation for compressible fluid, and the physical properties of oil-gas two-phase fluid. The effect of deformation on fluid film was considered, thus the thermal-fluid-solid coupling method was adopted and solved by finite element method. The effects of operating parameters (oil-gas ratio, rotational speed and pressure difference) on the dynamic performance of oil-gas miscible backflow pumping seal were analyzed. The results show that the viscosity of oil-gas miscible fluid is larger, which makes the seal have greater dimensionless stiffness, dimensionless damping and better dynamic characteristics. The deformation of seal ring reduces the dimensionless stiffness and increases the dimensionless damping, and the maximum influence is 16.9% and 31.2%. High speed increases the dimensionless stiffness and dimensionless damping, which is beneficial to the dynamic characteristics of the seal. While large pressure difference increases the dimensionless stiffness and decreases the dimensionless damping, which is not conducive to the dynamic characteristics. Therefore, the oil-gas miscible backflow pumping seal is suitable for oil-gas lubrication with high speed and low pressure difference.

Key words: oil-gas miscible, hydrodynamic seal, thermoelastic distortion, dynamic stiffness, dynamic damping

摘要：

研究了油气两相动压密封的动态特性。在可压缩流体雷诺方程中引入油气两相流体物性，建立油气两相流体的稳态和动态雷诺方程；考虑密封变形对流体膜的影响，采用热流固耦合方法并用有限元法进行求解；分析操作参数(油气比、转速和压差)对油气两相动压密封动态性能的影响。研究结果表明：油气两相流体的黏度较大，使密封具有更大的刚度系数、阻尼系数及更好的动态性能；密封端面变形减小了密封的刚度系数，增大了阻尼系数，且影响程度最大为16.9%和31.2%，对动态性能影响较大。高转速使刚度系数和阻尼系数增加，有利于密封的动态性能；而大压差使刚度系数增大、阻尼系数减小，不利于密封的动态性能；因此油气两相动压密封适用于高转速、低压差的油气润滑工况。

关键词: 油气两相, 动压密封, 热流固耦合, 动态刚度, 动态阻尼

CLC Number:

TH 117.2

Shicong LI, Caifu QIAN, Shuangxi LI, Lian CHEN. Study of thermal-fluid-solid coupling on dynamic characteristics of oil-gas miscible backflow pumping seal[J]. CIESC Journal, 2020, 71(5): 2190-2201.

李世聪, 钱才富, 李双喜, 陈炼. 油气两相动压密封动态特性的热流固耦合研究[J]. 化工学报, 2020, 71(5): 2190-2201.

Figures/Tables 13

References 40

1	束坤. 高速轻载航空轴承打滑监测技术研究[D]. 哈尔滨: 哈尔滨工业大学, 2015.
	Shu K. Research on monitoring technologies of high-speed and light-load aero-bearings skidding[D]. Harbin: Harbin University of Technology, 2015.
2	王跃飞, 孙启国, 吕洪波. 滚动轴承油气润滑及喷油润滑温度场对比研究[J]. 润滑与密封, 2014, 39(2): 66-70.
	Wang Y F, Sun Q G, Lyu H B. Comparing study on temperature field of rolling bearing under oil-air lubrication and spray lubrication[J]. Lubrication Engineering, 2014, 39(2): 66-70.
3	王振岭, 葛泉江, 林国昌. 航空发动机主轴轴承润滑与冷却技术研究[J]. 航空发动机, 2012, 38(3): 15-17+23.
	Wang Z L, Ge Q J, Lin G C. Research on lubrication and cooling technology of aeroengine main bearing [J]. Aeroengine, 2012, 38(3): 15-17+23.
4	李炎军, 陈国定, 刘亚军, 等. 航空发动机主轴承环下供油系统两相分相流动分析[J]. 润滑与密封, 2009, 34(5): 58-61.
	Li Y J, Chen G D, Liu Y J, et al. Two-phase fractional flow analysis of aeroengine main bearing inner-ring oil-flow system[J]. Lubrication Engineering, 2009, 34(5): 58-61.
5	曾群锋, 刘成, 张进华. 高速轴承油气润滑系统的研究及应用现状[J]. 润滑与密封, 2015, 40(3): 103-108.
	Zeng Q F, Liu C, Zhang J F. Application status and study of oil-air lubrication system for high speed rolling bearing[J]. Lubrication Engineering, 2015, 40(3): 103-108.
6	郭凯, 苑士华, 邵子桐. 喷射润滑高速轴承内部油气两相流动研究[J]. 北京理工大学学报, 2012, 32(10): 1022-1025+1041.
	Guo K, Yuan S H, Shao Z T. Study on oil-air two-phase flow inside the high-speed bearing cavity with jet lubrication[J]. Transactions of Beijing Institute of Technology, 2012, 32(10): 1022-1025+1041.
7	Krug M B, Peduto D, Kurz W, et al. Experimental investigation into the efficiency of an aero engine oil jet supply system[J]. J. Eng. Gas Turb. Power, 2015, 137: 011505.
8	Aidarinis J, Missirlis D, Yakinthos K, et al. CFD modeling and LDA measurements for the air-flow in an aero engine front bearing chamber[J]. J. Eng. Gas. Turb. Power, 2011, 133(8): 082504.
9	李小芬, 蔡纪宁, 张秋翔, 等. 低液气比混合润滑下的动压密封性能分析[J]. 润滑与密封, 2016, 41(4): 40-44 +81.
	Li X F, Cai J N, Zhang Q X, et al. Analysis on hydrodynamic sealing performance under low liquid-gas ratio mixed lubrication[J]. Lubrication Engineering, 2016, 41(4): 40-44+81.
10	李欢, 李双喜, 李小芬, 等. 油气两相动压密封端面结构多参数正交优化及试验研究[J]. 北京化工大学学报(自然科学版), 2017, 44(1): 76-84.
	Li H, Li S X, Li X F, et al. Multiparameter orthogonal optimization and experimental study on structure of air-oil miscible hydrodynamic seal[J]. Journal of Beijing University of Chemical Technology (Natural Science Edition), 2017, 44(1): 76-84.
11	陈炼, 李双喜, 李欢, 等. 油气两相回流泵送密封的端面温度分布分析及试验验证[J]. 润滑与密封, 2019, 44(5): 122-128.
	Chen L, Li S X, Li H, et al. Analysis and experiment verification on end-face temperature distribution of oil-gas two-phase backflow pumping seal[J]. Lubrication Engineering, 2019, 44(5): 122-128.
12	陈国定, 陈薄, 刘亚军, 等. 航空发动机轴承腔含油滴油气两相介质的流动模拟[J]. 西北工业大学学报, 2011, 29(1): 62-67.
	Chen G D, Chen B, Liu Y J, et al. Exploring through numerical simulation lubrication flow inside an aeroengine bearing chamber with film/droplet/air interactions taken into consideration [J]. Journal of Northwest Polytechnic University, 2011, 29 (1): 62-67.
13	吴昊天, 陈国定. 轴承腔油气两相泡状流动的数值研究[J]. 机械工程学报, 2008, 44(9): 70-75.
	Wu H T, Chen G D. Numerical research of two/phase oil-gas bubble flow in bearing chamber [J]. Journal of Mechanical Engineering, 2008, 44(9): 70-75.
14	刘德林, 姜涛, 何玉怀, 等. 浅论国内航空轴承的失效问题[J]. 失效分析与预防, 2015, 10(5): 324-330.
	Liu D L, Jiang T, He Y H, et al. Discussion on failure problems of aero-bearing[J]. Failure Analysis and Prevention, 2015, 10(5): 324-330.
15	Elrod H G, McCabe J T, Chu T Y. Determination of gas-bearing stability by response to a step-jump[J]. ASME J. Lubr. Technol., 1967, 89: 493-498.
16	Miller B A, Green I. Numerical techniques for computing rotordynamic properties of mechanical gas face seals[J]. J. Tribol.-T ASME, 2002, 124(4): 755-761.
17	陈东菊, 韩继弘, 高雪, 等. 基于非线性动态特性的轴承–转子系统振动分析[J]. 工程科学与技术, 2019, 51(1): 229-235.
	Chen D J, Han J H, Gao X, et al. Vibration analysis of bearing-rotor system based on nonlinear dynamic characteristics[J]. Advanced Engineering Sciences, 2019, 51(1): 229-235.
18	Varney P, Green I. Dynamic modeling of an eccentric face seal including coupled rotordynamics, face contact, and inertial maneuver loads[J]. Proc. IMechE Part J: J. Engineering Tribology, 2018, 232(6): 732-748.
19	Varney P, Green I. Steady-state response of a flexibly mounted stator mechanical face seal subject to dynamic forcing of a flexible rotor[J]. J. Tribol.-T ASME, 2017, 139(6): 062201.
20	Malanoski S B, Pan C H T. The static and dynamic characteristics of the spiral-grooved thrust bearing[J]. ASME J. Basic Eng., 1965, 87: 547-558.
21	Peng J P, Carpino M. Calculation of stiffness and damping coefficients for elastically supported gas foil bearings[J]. J. Tribol.-T ASME, 1993, 115: 20-27.
22	Zirkelback N, San Andres L. Effect of frequency excitation on force coefficients of spiral groove gas seals[J]. J. Tribol.-T ASME, 1999, 121(4): 853-863.
23	李双喜, 蔡纪宁, 陈罕, 等. 高速螺旋槽气体密封轴向微扰的有限元分析[J]. 北京化工大学学报, 2003, 30(1): 52-56+72.
	Li S X, Cai J N, Chen H, et al. Finite element analysis of axial perturbation of high speed spiral groove gas seals[J]. Journal of Beijing University of Chemical Technology, 2003, 30(1): 52-56+72.
24	陈源, 彭旭东, 李纪云, 等. 螺旋槽结构参数对干气密封动态特性的影响研究[J]. 摩擦学学报, 2016, 36(4): 397-405.
	Chen Y, Peng X D, Li J Y, et al. The influence of structure parameters of spiral groove on dynamic characteristics of dry gas seal[J]. Tribology, 2016, 36(4): 397-405.
25	许恒杰, 宋鹏云, 毛文元, 等. 考虑氢气实际气体效应和阻塞流效应的螺旋槽干气密封动态特性分析[J]. 化工学报, 2017, 68(12): 4675-4684.
	Xu H J, Song P Y, Mao W Y, et al. Dynamic characteristics of spiral groove dry gas seals with consideration of hydrogen real gas and choked flow effects[J]. CIESC Journal, 2017, 68(12): 4675-4684.
26	白少先, 魏佳, 朱得磊, 等. T型槽端面密封气膜热弹流润滑动态稳定性[J].摩擦学学报, 2019, 39(2): 131-139.
	Bai S X, Wei J, Zhu D L, et al. Thermoelastohydrodynamic gas lubrication of T-groove face seals: stability of sealing film[J]. Tribology, 2019, 39(2): 131-139.
27	宋鹏云, 胡晓鹏, 许恒杰. 实际气体对T槽干气密封动态特性的影响[J]. 化工学报, 2014, 65(4): 1344-1352.
	Song P Y, Hu X P, Xu H J. Effect of real gas on dynamic performance of T-groove dry gas seal[J]. CIESC Journal, 2014, 65(4): 1344-1352.
28	许恒杰, 宋鹏云. 三自由度微扰下的静压干气密封动态特性分析[J]. 排灌机械工程学报, 2017, 35(1): 56-64.
	Xu H J, Song P Y. Analysis on dynamic characteristics of aerostatic dry gas seals with three degrees of freedom perturbation[J]. Journal of Drainage and Irrigation Machinery Engineering, 2017, 35(1): 56-64.
29	尹源, 刘向峰, 丛国辉, 等. 外加压静压型机械密封均压槽设计对动态性能的影响[J]. 流体机械, 2017, 45(4): 15-21.
	Yin Y, Liu X F, Cong G H, et al. Influence of equalizing grooves design for externally pressurized hydrostatic mechanical seal on dynamic performance[J]. Fluid Machinery, 2017, 45(4): 15-21.
30	赵一民. 车用微槽型旋转密封环润滑状态预测与动态特性研究[D]. 北京: 北京理工大学, 2016.
	Zhao Y M. Study on lubricating condition prediction and dynamic characteristcs of grooved rotary seal ring for vehicle[D]. Beijing: Beijing Institute of Technology, 2016.
31	杨文静, 郝木明, 李振涛, 等. 考虑锥度及波度的螺旋槽液膜密封动态特性分析[J]. 化工学报, 2016, 67(12): 5199-5207.
	Yang W J, Hao M M, Li Z T, et al. Analysis of dynamic characteristics of spiral groove liquid film seal considering taper and waviness[J]. CIESC Journal, 2016, 67(12): 5199-5207.
32	陈洋洋, 朱维兵, 杨阳. 基于ANSYS Workbench的螺旋槽干气密封流固耦合分析[J]. 润滑与密封, 2017, 42(11): 119-123.
	Chen Y Y, Zhu W B, Yang Y. Fluid solid coupling analysis of spiral groove dry das seal based on ANSYS Workbench[J]. Lubrication Engineering, 2017, 42(11): 119-123.
33	陈汇龙, 李同, 赵斌娟, 等. 动压型机械密封内流场及性能的流固热耦合[J]. 排灌机械工程学报, 2017, 35(6): 502-507.
	Chen H L, Li T, Zhao B J, et al. Analysis of flow field and performances in hydrodynamic mechanical seal based on fluid-solid-heat interaction[J]. Journal of Drainage and Irrigation Machinery Engineering, 2017, 35(6): 502-507.
34	丁雪兴, 苏虹, 张海舟, 等. 螺旋槽干气密封热力耦合流场近似计算及分析[J]. 排灌机械工程学报, 2013, 31(9): 788-793+799.
	Ding X X, Su H, Zhang H Z, et al. Approximately analytical solutions of thermal-mechanical coupling flow field in spiral-grooved dry gas seals[J]. Journal of Drainage and Irrigation Machinery Engineering, 2013, 31(9): 788-793+799.
35	杨笑, 孟祥铠, 彭旭东, 等. 表面织构化机械密封热弹流润滑性能分析[J]. 摩擦学学报, 2018, 38(2): 204-212.
	Yang X, Meng X K, Peng X D, et al. A TEHD lubrication analysis of surface textured mechanical seals[J]. Tribology, 2018, 38(2): 204-212.
36	Li S Z, Guo G D. Content-based audio classification and retrieval using SVM learning[C]//Proceedings of ICME(IEEE International Conference on Multimedia and Expo). Tokyo, Japan: IEEE Computer Society 2001 Contents, 2001: 749-752.
37	阎昌琪. 气液两相流[M]. 哈尔滨: 哈尔滨工程大学出版社, 2007: 66.
	Yang C Q. Gas and Liquid Two-phase Flow[J]. Harbin: Harbin Engineering University Press, 2007: 66.
38	Li S C, Qian C F, Li S X, et al. Study of sealing mechanism of gas-liquid miscible backflow pumping seal[J]. Tribology International, 2020, 142: 105974.
39	Hu J P, Liu C P. Effect of working parameters on performance characteristics of hydrostatic turntable by using FSI-thermal model[J]. J. Cent. South Univ., 2018, 25(11): 2589-2600.
40	Ruan B. A Semi-analytical solution to the dynamic tracking of non-contacting gas face seals[J]. J. Tribol.-T ASME, 2002, 124(1): 196-202.

参数	数值	参数	数值
动环端面内径 r_in,R / mm	33.25	O形圈槽外径 r₁ / mm	41.5
动环端面外径 r_out,R / mm	43	静环外径 r₂ / mm	45
静环端面内径 r_in,S / mm	35.5	轴径 r₃ / mm	30
静环端面外径 r_out,S / mm	42	动环尾部外径 r₄ / mm	34
螺旋槽根径 r_g / mm	40	动环尾部倾斜角 σ /(°)	65
螺旋角 α /(°)	15	平衡半径 r_b / mm	36.75
槽深 h_g / μm	5	动环厚度 δ_R/ mm	13
槽堰比 γ	0.5	静环厚度 δ_S / mm	15
槽数 N_g	12	油气比 c	0.1

参数	数值	参数	数值
动环端面内径 r_in,R / mm	33.25	O形圈槽外径 r₁ / mm	41.5
动环端面外径 r_out,R / mm	43	静环外径 r₂ / mm	45
静环端面内径 r_in,S / mm	35.5	轴径 r₃ / mm	30
静环端面外径 r_out,S / mm	42	动环尾部外径 r₄ / mm	34
螺旋槽根径 r_g / mm	40	动环尾部倾斜角 σ /(°)	65
螺旋角 α /(°)	15	平衡半径 r_b / mm	36.75
槽深 h_g / μm	5	动环厚度 δ_R/ mm	13
槽堰比 γ	0.5	静环厚度 δ_S / mm	15
槽数 N_g	12	油气比 c	0.1

属性	动环	静环
材料	18Cr2Ni4WA	M234
弹性模量 E / GPa	207	11.3
泊松比 u	0.273	0.27
热导率 λ/(W·m^-1·K^-1)	35.58	140
比热容c_p/(J·kg^-1·K^-1)	499	690
热膨胀系数 α_l /K^-1	12.37×10^-6	5.5×10^-6
密度 ρ/(kg·m^-3)	7910	2400

属性	动环	静环
材料	18Cr2Ni4WA	M234
弹性模量 E / GPa	207	11.3
泊松比 u	0.273	0.27
热导率 λ/(W·m^-1·K^-1)	35.58	140
比热容c_p/(J·kg^-1·K^-1)	499	690
热膨胀系数 α_l /K^-1	12.37×10^-6	5.5×10^-6
密度 ρ/(kg·m^-3)	7910	2400

参数	数值	参数	数值
轴承腔内压力p_out/MPa	0.151	气体密度 ρ_gas/(kg·m^-3)	1.1774
轴承腔外压力 p_in/MPa	0.101	润滑油密度 ρ_oil/(kg·m^-3)	840
转速 ω / (r·min^-1)	8000	气体黏度 μ_gas/(Pa·s)	1.8462×10^-5
操作温度 T / K	300	润滑油黏度 μ_oil/(Pa·s)	4840×10^-5