化工学报 ›› 2019, Vol. 70 ›› Issue (1): 336-344.DOI: 10.11949/j.issn.0438-1157.20180960

• 材料化学工程与纳米技术 • 上一篇    下一篇

高温除尘碳化硅膜的制备及其抗腐蚀特性

李冬燕1(),魏巍2,韩峰2   

  1. 1. 南京科技职业学院化工与材料学院,江苏 南京 210048
    2. 南京膜材料产业技术研究院有限公司,江苏 南京 211100
  • 收稿日期:2018-08-27 修回日期:2018-10-25 出版日期:2019-01-05 发布日期:2019-01-05
  • 通讯作者: 李冬燕
  • 作者简介:李冬燕(1979—),女,副教授,<email>ldy790319@163.com</email>
  • 基金资助:
    国家重点研发计划项目(2016YFC0204000);南京科技职业学院科研项目(NHKY-2016-01);国家重点研发计划项目(2016YFC0204000);江苏高校青蓝工程项目;南京科技职业学院科研项目(NHKY-2016-01)

Preparation and corrosion resistance of SiC membrane using for dust removal in high temperature

Dongyan LI1(),Wei WEI2,Feng HAN2   

  1. 1. School of Chemical Engineering and Materials Nanjing Polytechnic Institute, Nanjing 210048, Jiangsu, China
    2. Nanjing Industrial Technology Research Institute of Membrane Material Co. Ltd., Nanjing 211100, Jiangsu, China
  • Received:2018-08-27 Revised:2018-10-25 Online:2019-01-05 Published:2019-01-05
  • Contact: Dongyan LI

摘要:

采用喷涂法在碳化硅(SiC)支撑体上覆膜,根据碳化硅材料的氧化特性,设计了有氧烧结和氩气烧结随温度转换的组合烧结制度,并通过优化保温时间降低碳化硅陶瓷膜烧结成本。研究结果表明,新的烧结制度能有效地控制有氧烧结阶段产生的二氧化硅(SiO2)量,并促进其与烧结助剂氧化锆(ZrO2)等在气氛烧结阶段的反应,反应生成的锆英石相和添加莫来石相共同形成SiC颗粒连接颈部。制备的碳化硅陶瓷膜平均孔径为3.03 μm,气体通量为175 m3?m-2?h-1?kPa-1。且在100℃的0.25 mol?L-1的H2SO4溶液和0.25 mol?L-1的NaOH溶液中腐蚀6 h后,膜层表面形貌无明显变化,具有较强的抗腐蚀性能。

关键词: 除尘, 碳化硅陶瓷膜, 气氛烧结, 保温时间, 耐腐蚀

Abstract:

Spray-coating was used to prepared silicon carbide (SiC) membranes on the surface of SiC supports, then the coated samples were sintered by switching sintering atmospheres (aerobic to argon) over different temperature ranges according to the oxidation characteristics of SiC, and the sintering cost of SiC ceramic membranes was reduced by optimizing the soaking time. The results revealed that the new sintering procedures can effectively control the oxidation of SiC in the aerobic sintering stage, and promoted its oxidation product silica (SiO2) reaction with the sintering aids such as zirconia (ZrO2) in the argon sintering stage. The average pore size of the prepared SiC ceramic membrane was 3.03 μm and the gas permeation was 175 m3·m-2·h-1·kPa-1. After etching for 6 h in 0.25 mol·L-1 H2SO4 solution and 0.25 mol·L-1 NaOH solution at 100℃, the surface morphology of the film has no obvious change and has strong corrosion resistance.

Key words: dust removal, SiC ceramic membrane, atmosphere sintering, soaking time, corrosion resistant

中图分类号: